17. Determine the maximum torque (in N-m), that can be applied to a hollow steel tube, without exceeding an angle of twist of 0.5 degree. The hollow tube has an OD= 30 mm, 1= 1.5 mm and L= 300 mm. Use G-80

17. Determine the maximum torque (in N-m), that can be applied to a hollow steel tube, without exceeding an angle of twist of 0.5 degree. The hollow tube has an OD= 30 mm, 1= 1.5 mm and L= 300 mm. Use G-80

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 6-splined shaft delivers a torque of 7.5 kN - m. The spline has the following dimensions: D = 75…

A: given; →torque(T)=7.5KN-m =7.5*106N-mm→outer diameter(D)=75mm→inner…

Q: Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts…

Q: e diameter

A: To find Outside diameter(d2)

Q: A circular shaft with 50mm and its lenght is 850mm long and is made of steel, the shaft is subjected…

A: GIVEN :- diameter : d=50mm length: L=850 mm Torque subjected: T=800Nm (to determine θ we need the…

Q: A solid stainless steel [G= 12,500 ksi] shaft that is 30 in. long will be subjected to a pure torque…

Q: Qs/The solid compound shaft, made of three different materials, carries the two torques shown in…

Q: Q-1 The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The…

Q: A motor drives a shaft at 300 rpm and a power output of 100 kW. The shaft is made of A-36 steel and…

Q: A steel tube with outer and inner diameters are 86mm and 52mm respectively is twisted by torques at…

Q: Determine the maximum torque (in N-m), that can be applied to a hollow steel tube, without exceeding…

Q: 2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm and b is…

A: Find the maximum torque .

Q: Compute the angle of twist (deg) in a 45-in circular steel shaft with a diameter of 42- mm that is…

A: Where: θ is the angle of twist in radians, T is the applied torque in pound-feet L is the length of…

Q: A hollow circular steel shaft with an outside diameter of 2.906. and a wall thickness of 0.437 in.…

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

Q: A solid stainless steel [G = 93 GPa] shaft that is 2 m long will be subjected to a pure torque of T…

Q: The bwo 3-ftlong shafts are made of 2014-16 aluminum. Each has a diameter of 1.5 in and they are…

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: diameter of pulley (d) = 110 mm no of belt = n = 2 groove angle = 2β = 45° = β = 22.5° power…

Q: Q1 The rotating solid steel shaft is simply supported by bearings A and B, the gear has 500-mm pitch…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Section 12-1 to 12-6 For the shaft subjected to the external torque in each of Figs. P12-1 to P12-6,…

Q: Problem 1: Determine the internal torque in the shaft shown at A, B, and C. Show the free-body…

Q: Calculate the shaft diameter necessary to support a combined maximum bending moment of 2000 Nm, and…

Q: Estimate the shaft diameter required to produce a critical speed of rotation of 638 rpm for a steel…

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

Q: A solid circular drive shaft connects a motor to gears B and C. The drive shaft is steel (G= 66 GPa)…

Q: A solid circular steel shaft having an outside diameter of 1.50 in. is subjected to a pure torque of…

A: The given information in the problem is shown in the following attached image:

Q: A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…

Q: (3) For the shaft shown in the Figure, compute the maximum torque T that can be applied., B T…

Q: Oh no! The bearing at the wall on the left has been damaged. It is now acting like another gear that…

Q: The 55-mm-diameter A992 steel shaft is subjected to the torques shown where T = 900 N-m. Part A…

A: Given: Diameter, d = 55 mm Shear modulus of A992 steel shaft, G = 75 GPa T = 900 N.m LAD = 600 mm…

Q: What is the maximum diameter (mm) of a solid steel shaft that will not twist through more than 3…

A: Given: Maximum twist allowed, θ=3°Length of the shaft, L=6 mTorque applied, T=14 kN.mShear modulus,…

Q: naft has a diameter of 41mm. The PCD of the coupling bolts is 63mm. amter is 3mm, and the yield…

A: Given data-T=354Nm D=41mmPCD=63mm

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

17. Determine the maximum torque (in N-m), that can be applied to a hollow steel tube, without exceeding an
angle of twist of 0.5 degree. The hollow tube has an OD = 30 mm, t = 1.5 mm and L=300 mm. Use G = 80
GPa.
a. 63.6
b. 72.1
C.
d.
80.3
86.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pravinbhai
A solid stainless steel [G = 108 GPa] shaft that is 1.2 m long will be subjected to a pure torque of T = 82 N-m. Determine the minimum diameter d required if the shear stress must not exceed 40 MPa and the angle of twist must not exceed 4.7°. Report both the maximum shear stress 7 and the angle of twist at this minimum diameter. Answers: d = mm. T = IN i MPa. i
ANSWER ASAP
Write legibly, provide given, step by step manual solution , and diagram for below problem. Determine the maximum diameter of a taper pin for use to fix a lever to a shaft, if it is to transmit a maximum torque of 750 in-lbs. The shaft diameter is 3 inches and the material allowable stress is 17000 psi. Use factor of safety of 2. (Ans. d = 0.1935 in)
A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?
A 2in diameter shaft is made of aluminum 2014-T6, and has a torque of 1/2T, -T and 2/3T respectively along its length measured from the free end with the distance of 12 inches between its section. If the factor of safety of 3 is used and the angle of twist is limited such that it does not exceed 0.1 rad. find the maximum allowable tonque T in the shaft in ksi
Question 48 A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)-28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T1" developed at left fixed support at a is____KN-m (A) 5.03 B) 3.82 C) 2.64 D) 0.48 (E) 1.18
Q5: Select A suitable spline having a fit B for a gear to be mounted on a shaft with a diameter D= 60 mm. The gear transmits a torque of T=2.3 x 106 N.mm and has a hub length of L=100 mm.