17. A reversible non-flow, constant volume process decreases internal energy by 316.5 kJ for 2.268 kg of a gas for which R = 430 J/kg-K and k 1.35. For the process, determine the work, heat, change entropy. The initial temperature is 204.4°C.

17. A reversible non-flow, constant volume process decreases internal energy by 316.5 kJ for 2.268 kg of a gas for which R = 430 J/kg-K and k 1.35. For the process, determine the work, heat, change entropy. The initial temperature is 204.4°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: An insulated mixing chamber receives 2 kg/skg/s R-134a at 1 MPa, 100 ∘C in a line (state-3). Another…

A: To solve this problem, we will use the conservation of mass and energy principles along with the…

Q: A- An air conditioner compressor 134a at 4 bar, 20 °C and 6 m³/min which is steadily compressed to…

Q: 1. Steam enters an insulated turbine at a pressure of 1 MPa and temperature 200°C, and exits at 40°C…

A: Find the power developed and change in specific entropy.

Q: A gas initially at 850 mm Hg is compressed polytropically in an Engine. During the process, the…

A: According to Bartleby guidelines, we can solve only one question at a time. You are requested to…

Q: 5. Assume 5 lb of an ideal gas with R = 38.7 ft-b/lb-<R and k = 1.668 have 300 Btu of heat added…

Q: Four pounds of air gain 0.491 BTU/ °R of entropy during a non-flow isothermal process. If p: = 120…

A: Using entropy expression of closed system to solve the problem

Q: Entropy generated due to the heat transfer

A: Given data; An amount ,Q=100kwOne side of wall is maintained ;T1=1270C=127+273=400 KOther side of…

Q: 3.82 A Carnot engine operates between 37 Cand347 C. If the engine produces 620 kJ of work, the…

A: Entropy is the measure of disorderness of any system. If heat flow occurs through any system, then…

Q: A closed gaseous system undergoes a reversible process during which 25 BTU are rejected, and the…

A: Answer: The change in internal energy is 2.7635 BTU.

Q: Water contained in a closed, rigid tank, initially at 100 lbf/in², 800°F, is cooled to a final state…

Q: A quantity of gas at 1.4 bar and 25 oC occupies a volume of 0.1 m3 in a cylinder behind a piston is…

A: Introduction: The reversible compression of the gas occurs in an endless number of tiny stages, with…

Q: pressed liquid water enter poiler at 500°C, 3000 kPa

A: Write the value of enthalpy from the steam table as follows-

Q: (B) 0.56 m3 of air at a temperature of 250°C and a pressure of 6.5 bar expand according to the law…

A: Thermodynamics : It is a branch of science that deals with work, heat, and energy. Also, it studies…

Q: Problem 2. Entropy Balance Using Table of Properties A piston-cylinder assembly contains 3 kg of…

Q: Q.) A piston-cylinder device contains air at initially 1000 kPa and 200°C. The air is first expanded…

Q: A mass of 6 kg of air is compressed from 95 kPa, 38 0C to 620 kPa in a polytrophic process, PV1.3…

A: Given Data→ Mass of air m=6 kg Pressure and temperature at the inlet P1=95 KPaT1=38°C Pressure after…

Q: Carbon dioxide gas is compressed at steady state from a pressure of 20 lbț/in? and a temperature of…

Q: Steam at 50 bar and 600°C enters an adiabatic turbine and leaves as saturated vapor at 1.5 bar. The…

A: The given values are :

Q: Part II 11. Two lbm of air initially at P₁= 15 psia and T₁ = 150 °F undergoes a cycle consisting of…

A: "Since you have posted with multiple sub parts, we will provide the solution only to the first three…

Q: Water vapor enters a turbine with a mass flow of 2kg / h, 6 MPa pressure, 500 ° C temperature and 40…

Q: cylinder there is 6 m ^ 3 of an ideal gas at a pressure 1 bar .This gas is compressed in a…

A: Given:Volume of gas, V=6 m3Pressure of gas, P1=1 barfinal pressure of gas, P2=5 bar

Q: The turbine of a vapor power plant its schematics is shown in Figure Q6 is evaluated for entropy…

Q: steam turbine operates with an inlet condition of 30 bar, 400 0C, 160 m/s and an outlet state of a…

A: Given Data P1=30 bar, T1=400°C, V1=160 m/s P2=0.7 bar, sat vapor, V2=100 m/s P=10800 kW Mass flow…

Q: Part D only Consider a piston-cylinder device containing m = 1 kg of air at the initial temperature…

Q: he entropy change of an irreversible process can be calculable. A.(True) B.(Fale)

Q: Q/Fluid at 15 bar is contained in a cylinder behind a piston, the initial volume being 0.01 m3.…

Q: PART B only Consider a piston-cylinder device containing m = 1 kg of air at the initial temperature…

Q: Steam @ 500°C and 3500 kPa enters a nozzle at a velocity of 30 m/s and leaves as saturated vapor at…

A: Tin=500°CTin=773 K Pin=3500 kPa , v1=30 msecPexit=100 kPa and q˙=128 kjsec T0=25°C T0=298 K

Q: 1 kg of air at 700 K and 1.1 MPa in a piston and cylinder devices undergoes a reversible and…

Q: Q2) A piston-cylinder device contains air at initially 1.5 bar and 25°C. The air is first compressed…

A: Givenprocess 1-2PVk=constantP1=1.5barT1=25oCP2=7barV2=0.05 m3k=1.4process 2-3PV=constantP3=P1=1.5…

Q: .A fluid at a pressure of 300 KPa and with specific volume of 0.18 contained in kg a cylinder behind…

Q: A well-insulated turbine operating at steady state with a steam flow rate of 40 kg/s It produces MW…

Q: 3. In a cycle, a 4kg ideal gas (MW=3g/mol and k=2.3) confined in a controlled mass system went…

Q: 1. A closed tank, V = 10 L, containing 5 kg of water initially at 25 ° C, is heated to 150 ° C by a…

A: The step by step solution is given below.

Q: 200Kg/min superheated steam at 40 bar and 350C enters a turbine through a 7.5cm ID pipe. It exits at…

Q: The entropy change of a system can be negative, but the entropy generation cannot.

A: Entropy is defined as the property that represents the variation in the different property of the…

Q: A reversible power cycle whose thermal efficiency is 37% receives 50 kJ by heat transfer from a hot…

Q: A scientist is observing a boiler wherein steam generated at 204.44 F using 11.02 lbs of water at…

Q: The entropy change between two specified states is the same whether the process is reversible or…

Q: A heat engine used a steam as working fluid has 3 kg/s and initial the steam undergoes to expansion…

Q: kJ Air (Rair = 0.287 ) as an ideal gas flows through the turbine and heat exchanger arrangement…

A: INTRODUCTION : A turbine is a steady flow energy device, in which energy and mass enter into and…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

17.
A reversible non-flow, constant volume process decreases internal
energy by 316.5 kJ for 2.268 kg of a gas for which R = 430 J/kg-K and k
1.35. For the process, determine the work, heat, change entropy. The
initial temperature is 204.4°C.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

b) A nearly flat bicycle tire becomes noticeably warmer after it has been pumped up. Approximate this process as a reversible adiabatic compression. Take the initial pressure and initial temperature of the air before it is put in the tire to be P = 1.00 bar and T; = 298 K. The final volume of the air in the tire is V = 1.00 L and the final pressure is Pf = 5.00 bar. Hints: • Cy.m = 5/2 R. Heat Capacity ratio, y = Cp.m Cy,m = 1.4 %3D Cy,m For a reversible adiabatic change, 4 = (4 )°, where c = R For perfect gas: CP.m - Cv,m = R CP.m and Cv.m denote molar heat capacity at constant pressure and volume, respectively. Tand V are temperature and volume at initiate (i) state ad final (f) state. i) Derive a mathematical expression to show the relationship of temperature, volume and heat capacity ratio (y) for the transformation of this process from initial to final states.
Steam enters the nozzle operating a steady state pressure of 2.5 MPa and a temperature of 300 °C ( H1 = 3008.8 kJ/kg) and leaves at a pressure of 1.7 MPa with a velocity of 470 m/s. The rate of flow of steam through the nozzle is 1360 kg/hr. Neglecting the inlet velocity of the steam and considering the flow in the nozzle is adiabatic, find:a. the exit enthalpy in kJ/kg, ( H2)b. the nozzle exit area ( in cm) if V exit is 0.132 m^3 /kg c. the system
Helium is contained in a balloon at 0.5 m3, 100 °C inside an evacuated, insulated chamber. The balloon is suddenly punctured, allowing the helium to expand into the chamber with a volume of 5 m3. Treat the helium as an ideal gas. How much entropy is generated per kg of helium? Why does this process generate entropy?
13. During a reversible process, 2.09 kg/s of gas rejects 322.9 kJ/s of heat isothermally at 25.5°C. For this gas, cp = 2.14 kJ/kg K and c, 1.62 kJ/kg K. The initial pressure is 551.7 kPa. Determine the work steady flow of the process in hp if APE = 2.8 kJ/s and AKE = 6.2 kJ/s.
Two kg water at 95°C with a quality of 40% has its temperature raised 15°C in a constant volume process. What is the new specific entropy? Select one: a. 3.618 kJ/kg K b. 4.015 kJ/kg K c. 6.747 kJ/kg K d. 5.232 kJ/kg K
1
4*. Steam at 2 MPa and 450° C enters an isentropic nozzle with a velocity of 10 m/s and exits at 1.5 MPa. The mass flow rate is 0.2 kg/s. Calculate: a) The exit temperature. b) The velocity of the steam at the exit of the nozzle. c) The area at the exit of the nozzle.
7. If 10 kgm/min of air are compressed isothermally from p1 = 96 kPa and V₁ = 7.65 m³/min to p2 = 620 kPa, find the work, the change of entropy and the heat for (a) nonflow process and (b) a steady flow process with u₁ = 15 m/s and U₂ = 60 m/s. Ans. (a) -1370 kJ/min, -5.356 kJ/K.min; (b) -1386.9kJ/min
An air enters a compressor at 120 kPa, 20 C with volume flow rate of 10m^3/min. It then exits the compressor at 1.5Mpa and 145 C. Calculate the power input to drive the compressor (under steady state) when heat transfer from the compressor is 2 kW.
determine if it its true or false
(%25) Q1. A tank is perfectly insulated and divided into two parts by a membrane. The first part occupies 5 m³ volume containing air at 100 kPa pressure and 300 K temperature and the second one 2 m³ air at 2 MPa and 300 K. The membrane suddenly raptures somehow, and then thermodynamic equilibrium is established. (a) Find the final temperature, pressure and entropy change of air, (b) Calculate the entropy generation during this process.