16. What is the equivalent length of 10 cast iron 3/4-in. I.D. standard 90° elbows placed in a hydraulic circuit which carries 48 gal/min of a hydraulic fluid with a Sg of 0.86 and a kinematic viscosity of 0.04 Newts?

16. What is the equivalent length of 10 cast iron 3/4-in. I.D. standard 90° elbows placed in a hydraulic circuit which carries 48 gal/min of a hydraulic fluid with a Sg of 0.86 and a kinematic viscosity of 0.04 Newts?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

400mm Kerosene, SG=0.82 Air, SG=0.0012 Benzene, SG= 0.88 100mm 200rim 150mm 90mm Water Hg What is the pressure difference between the pipes of air and benzene?Use SG of mercury as 13.6.
16. If oil has an absolute viscosity of 510 poises, what is its viscosity in the fps system?
Q1/ Explain the pressure loss in the four- section petroleum well drilling system 1. Surface connections. 2. Pipes including drillpipe, heavy walled drillpipe and drill collars. 3. Annular areas around drillpipes, drillcollars, etc. 4. Drillbit. Note: The explanation is in text format, with the equations and drawings, if any, mentioned
Ex. 10. A mercury manometer is con- nected to open tank of fuel. Calculate a change of manometer reading h if a level of fuel increases about A H. (Ans. Ah = AH ps/(2pm - Ps)) Ex. 11. In well-type manometer (with constant zero level) there is neglected a change of fluid level in w big vessel (diameter D). Calculate a ratio d/D for which an error connected with a change of fluid level AH is less than 1%. (Ans. d/D < 0.1) oil fuel D ΔΗ mercury ΔΗ Ο
What horsepower is supplied to air moving at 20 fpm through a 2 x 3 ft duct under a pressure of 3 in. water gage?
13. A U-tube differential manometer connects two pressure pipes A and B. Pipe A contains carbon tetrachlo- ride having a specific gravity 1.594 under a pressure of 1.772 N/cm and pipe B contains oil of sp. gr. 0.8 under a pressure of 11.772 N/cm. The pipe A lies 2.5 m above pipe B. Find the difference of pressure measured by mercury as fluid filling U-tube. (A.M.I.E. December, 1974) (Ans. 31.36 cm of mercury]
FROM THE ATTACHED SKETCH, THE GIVEN DATA ARE AS FOLLOWS: Pressure loss due to friction a. Reservoir tank =50,000 liters of water b. Total Static head is 30 ft. Pressure loss in plastic pipes (feet of water per 100 ft of tube) c. Pipe material is plastic and 1.5-inch diameter. d. There are four 90-degree elbows, one gate valve and one open swing spm 0.5 in. 0.75 in. 1 in. 1.5 in. 2 in. 3 in. 1.4 4.8 0.0 0.0 0.0 0.4 0.1 0.4 0.8 1.3 1.9 2.7 0,0 0.0 valve. 0.0 1.2 2.5 4.2 6.3 8.8 15.2 26.0 49.7 86.9 e. Total pipe length is 50 ft. 3 0.0 10.0 17.1 25.8 36.3 63.7 97.5 0.0 0.1 0.2 0.2 0.3 4. 0.0 0.0 5 0.0 0.0 0.0 0,0 0.0 6 0.1 0.2 0.3 0.5 0.9 0.1 COMPUTE THE FOLLOWING USING THE PROVIDED TABLE BELOW. 8 4.6 0.6 10 15 20 6.9 14.6 0.8 1.7 2.9 0.0 25.1 1. IF THE TANK IS TO BE FILLED WITHIN 661.35 MINUTES WHEN EMPTY, COMPUTE HOW MANY GALOONS PER MINUTE (GPM) PUMP CAPACITY IS NEEDED TO FILL UP THIS TANK., USE 3.78 LITERS/GAL Pressure loss in valves and elbows (expressed in equivalent length of tube)…
Answer question 4
Subject: Hydraulics What is the specific weight of air at 480 kpa absolute and 21 degrees Celcius?
10. Identify the type of manometer in the following figures and then compute for the pressures. Open p.- Pr = ? SG-0.8 3 in. (SG = 0.80) h = ? 12 in. -Water glycerine A. (SG 1.26) Mercury (SG = 13.55) Salt Water P.= ? Mercury SG - 13.6 PA= 0.50 psi CRS 75cm 75cm h, - 150cm
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 2, P2(gage)=______ A. B. C. D. patm
PLEASE ANSWER QUESTION # 2 ONLY, DISREGARD THE OTHER PROBLEMS GIVEN. SHOW COMPLETE SOLUTION. THANK YOU. Intravenous infusions usually are driven by gravity by hanging the fluid bottle at sufficient height to counteract the blood pressure in the vein and to force the fluid into the body (fig. below). The higher the bottle is raised, the higher the flow rate of the fluid will be. An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. QUESTION #1: the mass change in the tank (sample answer: 20,287.65 lb. round off to 2 decimal place QUESTION #2: the water level in the tank 15 min. later (sample answer: 20,287.65 ft round off to 2 decimal place QUESTION #3: the volume change in the tank (sample answer: 20,287.65 cu ft round off to 2 decimal place