16. A wye connected load has a 5L20° ohm impedance per phase is connected across a120 volts three-phase source. Calculate the line current.24A15.45A41.56A13.85A17. A capacitor in series with a 200 ohm resistor draws a current of 0.3 ampere from120 volts, 60 hz AC supply. What is the value of the capacitor in microfarad?8.657.656.755.7618. A capacitor is rated 100 KVAR, 380 V, 50 Hz. What will be its kyar rating at 220V,60 Hz supply?50.740.226.7557.722Most loads are either inductive or capacitive, which of the following is not reactive innature?MotorsPCLight BulbsSprinkler23It is the ratio of measured voltage to the measured current of an electrical load circuit.resistanceresistancehot resistancecold resistance24. What is the phase sequence of a balance three phase circuit for which Van =160L30 and Vcn - 160L-90?abs.bbaacbaab

In this question we will find line current of star connection...Series connected RC circuit…

16. A wye connected load has a 5L20° ohm impedance per phase 120 volts three-phase source. Calculate the line current. 24A 15.45A 41.56A 13.85A 17. A capacitor in series with a 200 ohm resistor draws a current 120 volts, 60 hz AC supply. What is the value of the capacitor in m 8.65 7.65 6.75 5.76 18. A capacitor is rated 100 KVAR, 380 V, 50 Hz. What will be its 60 Hz supply? 50.7

16. A wye connected load has a 5L20° ohm impedance per phase 120 volts three-phase source. Calculate the line current. 24A 15.45A 41.56A 13.85A 17. A capacitor in series with a 200 ohm resistor draws a current 120 volts, 60 hz AC supply. What is the value of the capacitor in m 8.65 7.65 6.75 5.76 18. A capacitor is rated 100 KVAR, 380 V, 50 Hz. What will be its 60 Hz supply? 50.7

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase inductive load draws 10 MW at 0.6 power factor lagging. What is the value of the capacitor to be connected in parallel with the load to raise the power factor to 0.8? System voltage is 1000 V and system frequency is 50 Hz.
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
QUESTION 4 A resistor, a capacitor, and an inductor are connected in series with a function generator. The resistor has a resistance of 1.5k2, the inductor has a reactance of 1.2kQ, and the capacitor has a reactance of 2002. The circuit has a total current of 172mA RMS. Find the total voltage. O 310V233.7 O 74.5VL-14° 188V273.2 O 44.4VL-25.3°
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95%. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
When a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3
Desian aproblem for wye delta transform adions Determinc the eauivalend resistance between the terminals A andA B.
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
An inductive impedance made up of a resistor and an inductor has the characteristic that its currentadvances in phase to the voltage at the impedance A) lags in phase with the voltage across the impedance B) is in phase with the voltage across the impedance. C) None of the above
3. An inductor having a 50 ohms resistance and 100 ohm inductive reactance is connected to a 100 volts, 60 hz a-c source. Draw the phasor diagram and waveform diagram of the current and voltage of the circuit showing their phase an
Sine wave A has a positive-going zero crossing at 40°. Sine wave B has a positive-going zero crossing at 45°. Determine the phase angle between the two signals. What signal leads ? A Y-connected system can have wires. The (resultant) voltage between the hot legs (135V) is The phase angle between the phase voltage and the line voltage of a A-connected generator is degrees. The phase current produced by a certain 20V, Y-connected generator is 12A. The corresponding line current is A certain A-connected generator produces phase voltages of 30V. The magnitude of the line voltages are When the turns ratio of a transformer is 20 and the primary ac voltage is 6V, the secondary voltage is If 20W of power are applied to the primary of an ideal transformer with a turns ratio of 8, the power delivered to the secondary load is The turns required to match a 500 source to a 1000 load is
Draw roughly the arc characteristics in alternating currents with a frequency of 50 Hz and 500 Hz, explain briefly
An inductor and a 470 ohm resistor are connected in series with a function generator. The current is 53.7mA RMS 8kHz. The reactive power is 2.32 var. Find the value of the inductance.