[15%] PROBLEM #03 Anti-aliasing Filter a. [10%] A signal is generated by an LVDT with equation of v(t) = 1.2sin(4πt) +n(t) where n(t) = 1.0sin(240лt) is the noise contaminating measurement result. The signal, i.e., v(t) is recorded using a data acquisition system with sampling rate ƒ、 = 100Hz without anti-aliasing S filter. Draw the spectrum of the signal before and after sampling process. b. [5%] Determine the best value of the anti- aliasing corner frequency (cut-off frequency).

[15%] PROBLEM #03 Anti-aliasing Filter a. [10%] A signal is generated by an LVDT with equation of v(t) = 1.2sin(4πt) +n(t) where n(t) = 1.0sin(240лt) is the noise contaminating measurement result. The signal, i.e., v(t) is recorded using a data acquisition system with sampling rate ƒ、 = 100Hz without anti-aliasing S filter. Draw the spectrum of the signal before and after sampling process. b. [5%] Determine the best value of the anti- aliasing corner frequency (cut-off frequency).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 6 SPM(t) and Sy(t) as defined below, are the phase modulated and the frequency modulated waveforms, respectively, corresponding to the message signal m(t) shown in the figure. SPMt) = cos(1000nt + K, m(t)) and SEMI) = cos 1000rt + K m(t) dt %3D -0- where K, is the phase deviation constant in radians/volt and K, is the frequency deviation constant in radians/second/volt. If the highest instantaneous frequencies of SPM(t) and Kp is SEM1) are same, then the value of the ratio seconds. AV in m(t) 10 1 3 6 7 t (sec)
alacaklardır. C=A+B, D=A-B, k АВ+ВА |AB-BA| to be ; ve z = C |D| Find the fundamental period of the signal X (t). A=1 B=5 x(t) = AB.cos(kt + 1) – BA. sin (zt – 1) O a. 2*pi O b. 6*pi/17 О с. рі/7 O c. O d. pi/3 Ое. 11*pi/9
í given as: - - Suppose that the solution. continuous-time input x(t) to the system x(t)= M + cos (4000 π t) + cos (1000 π t) a- What sampling rate is required such that no aliasing occurs for signal x(t)?f=20kHz b- State whether or not has been aliased. c- Sketch the spectrum for the sampled signal from 0 to 20 kHz. M=36
BEI wenty speech signal each bandlimited to 4 kHz are FDM/SSB multiplexed, then RF modulated by a main carrier using AM modulator. Draw the block diagram and find the minimum bandwidth of multiplexing and final transmission bandwidth. A- Plot the amplitude and phase spectrum for the f(t) = 4cos(nft +30°) + 2 sin(aft)
please answer this question
Q5- If an information signal x ( t ) = cos(2π700t) +10cos(2π5000t) . Write the formula ofthe frequency modulation ( FM ) when Ac = 20 , Fc = 10 ^ 8 Hz, Kf = π 2000
Which of the following statement/statements about amplitude modulation is/are true? A The total power (Pt) in an AM signal is expressed as (P B C D P₁ = Pc+ ma 2 The modulation index is given as Ac Am When more than one sinusoids with different amplitudes are used to amplitude modulate a carrier, the overall modulation index for AM is- m₁ = √ (m², + m² ₂ + m² 3 + ...) 1 When ma = 1, only of the total power is in the sidebands and 3 2 remaining is in the carrier. 3 Submit
Q/find the ROC of the signal: æ(n)= 0.8"u(n)-1.3"u(-n – 1)
1,1•K/s "| Asiacell 2_53008416574... Electrical Engineering Department Subject: Eng. Analysis Class: 3 stage-Evening study Date: 21 /2/2021 Time: 1.5 Hours. Examiner:Lect.Hussein Tuama Еxam: Mid Q1-A) Determine the half range Fourier Sine Series for the function f(t) = sin t ost2 Q1-B) suppose x(t) has Fourie transforms of x(2t) and x(t + 1) X(@) = e-w etermine Q2-A) Find Inverse Fourier transform of f(w) A Q2-B) Find the power of the following signal f(t) = sin?t Cos3t Q3) If f(z) is analytic function and u(x, y) = x³ – 3xy find f(z) O O D
I need the answer as soon as possible
Please solve this question fully with explanation. Thank you.