? given as: - - Suppose that the solution. continuous-time input x(t) to the system x(t)= M + cos (4000 π t) + cos (1000 π t) a- What sampling rate is required such that no aliasing occurs for signal x(t)?f=20kHz b- State whether or not has been aliased. c- Sketch the spectrum for the sampled signal from 0 to 20 kHz. M=36

? given as: - - Suppose that the solution. continuous-time input x(t) to the system x(t)= M + cos (4000 π t) + cos (1000 π t) a- What sampling rate is required such that no aliasing occurs for signal x(t)?f=20kHz b- State whether or not has been aliased. c- Sketch the spectrum for the sampled signal from 0 to 20 kHz. M=36

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. a) Sketch the spectrum of the message signal x, (t) =4 sinc(2f) cos(6tt) and then find bandwidth and minimum sampling frequency. ninin b) The signal x, (t) is time division multiplexed with the signal whose spectrum is given in Figure 1(a). Prior to multiplexing, both signals are sampled separately. If the sampling of the both signals will be done with same minimum frequency, then how the sampling frequency should be selected? X2(f) -2.5 f(Hz) 2.5 Figure 1(a)
What is the basic concept of Fourier theory as it relates to real-world signals? How does the transfer function of a filter relate to this concept?
What will happen to the demodulated signal if the value of the capacitor ofthe parallel RC at the output is too high? If too low?
What is the relationship between the analog signal frequency F and the digital signal frequency f? (T is the period of the sampling period)a. F = f * Tb. F = F * Tc. No connectiond. Nothing is right
4. SAMPLING a. Suppose x(t) = 2 + cos(2n * 500 +t) + 5 * sin(2n + 1500 + t) was sampled/ Determine the necessary sampling period and frequency to prevent aliasing or folding, If the signal is sampled at 2 kHz to obtain x[n], what can be said about the sampled sequence, aliasing, folding? b. The signal with the spectrum has Fmax = 2000HZ, draw the spectrumof the sampled signal for Fs - 4000 ve Fs = 5000. -Fmaz Fnar
Consider the following continous time signal x(t). Assume that the signal was sampled at a sampling frequency of 20 Hz. Plot the magnitude spectrum of the sampled signal as a function of cyclic frequency. Be sure to include n values of up to +-2. Label x and y axis. Did aliasing occur? If so, what is the aliased frequency? x(t) = 1 + 2cos(2pi25t)
Discuss the concept of Smart Grids in power systems. How do Smart Grid technologies improve grid reliability, efficiency, and the integration of renewable energy sources?
A signal defined as x(t)=ejwot is periodic with a base period of T0=2π/w0. Is the X[n]=X(nT)=ejwonT signal obtained by sampling this signal with the time interval T periodic for the value T=T0/2, and if it is periodic, what is its basic period?
I need the answer as soon as possible
Compute the eight-point DFT of the sequence x(n) using radix-2 decimation-in-time. Follow exactly the corresponding signal flow graphs and keep track of all the intermediate quantities by putting them on the diagram. x(n)=1/2.sin(pie/4.n),0<=n<=?
Frequency spectrum of a signal is given as the following: a) Write an equation for the signal x(t) defined by this frequency spectrum. b) What is the minimum sampling frequency to sample this signal? c) Write x[n] after the signal digitized by an ADC with a sampling frequency of 2 Hz.
need help - nyquist and sampling process