15.a. How can a poorly attached connector affect signal strength in a fiber optic cable? A. Insertion loss can decrease. B. Return loss can decrease. C. Splice loss can increase. D. Return loss and insertion loss can increase.

Q: What is the maximum allowable distance for horizontal cabling? 100 m

A: The horizontal option secures and separates the cables while within the rack. While moving up or…

Q: Q3]Design a rectangular microstrip patch antenna to resonate at a frequency of 1=2GHZ, using a…

A:

Q: The coaxial cable connection that is most commonly used is   a) BNC b) N-series c) S-type a) BNC…

A: Given that: The coaxial cable connection that is most commonly used is   a) BNC b) N-series c)…

Q: Draw the layout of the Straight-Through and Rolled cable.

A: Straight-Through are  the type of cables that have the pins on each end of the cable. In such…

Q: J) Describe crossover cables.

A: Question j. Describe crossover cables.

Q: 13. The total loss in a fiber link is 5.2 dB, the design margin is 0 dB, and the optical budget is…

A: Solution:-    Fiber link loss = 5.2 dB     Design margin = 0 dB Optical budget  = 3.3 dB   To check…

Q: 28.A. If an optical fiber that operates at fast data rates has been designed to minimize the main…

A: Optical fiber are exceedingly thin strands of very high purity silica (glass) that transmit light…

Q: 4. Design equation F(A,B,C,D)=E(1,2,3,6,8,10,12,13,15) using a 4×1 Mux?

A: A 4X1 mux, also known as a 4-to-1 multiplexer, is a digital circuit that selects one of four input…

Q: TASK 1 a) Chanel bandwith is 4 kHz. The signal is sampled every 0,5 ms. The noise ratio is SNR=30…

A: In telecommunications, it is crucial to know how fast data can be transmitted over a given…

Q: 6. Loss in signal power as light travels down the fiber is called? a. Attenuation b. Propagation c.…

A:

Q: 1) if VBB=10V and VCC=20V, IC=? 2) If VBB=10V and VCC=20V, VCE=? 3) If VCC=25V, how much is the…

A: if VBB=10V and VCC=20V, IC=? 2) If VBB=10V and VCC=20V, VCE=? 3) If VCC=25V, how much is the…

Q: b)how does FWHM apply to an led s characteristics? c) draw the cross sectional view…

A: ANSWER: FWHM apply to an led s characteristics: In the field of LED illuminated presentation, the…

Q: P1.6 The transmission line shown in figure 1.10 has a steady-state incident voltage of 21 V and a…

A:

Q: A 24 telephone channels network, each band limited to 3.4 kHz, are to be time division multiplexe by…

A: According to the information given :- We have to follow the instruction and calculate the bandwidth.

Q: signal waveform is filtered by an ideal LPF before transmission. channel using PAM. Each signal is…

A: The sampling hypothesis indicates the base sampling rate at which a constant time signal should be…

Q: How do you obtain a list from a string? Suppose s1 is welcome. What iss1.split('o')?

A: . A programming language uses lists to store a large number of sequential collection of elements. .…

Q: 2. If the period of a PWM signal is 1500 counts and the desired duty cycle is 20%, what is the pulse…

A: 1) The duty cycle describes the amount of time the signal is in a high (on) state as a percentage of…

Q: In the Maxwell bridge shown in Figure2, let the fixed-value bridge components have the following…

A: For the given Maxwell bridge we need to find unknown Inductance , resistance and quality factor.

Q: bandwidth

A: Given : - The concept of signal to noise ratio and  power of the signal as specified in the above…

Q: Question 35 Good hardline coaxial cable cores require at least O6 in or 15 cm O12 in or 30 cm 3 in…

A: The correct answer for the above mentioned question is given in the following steps for your…

Q: e maximum capacity of the channel.

A: Solution  part (a)  :- In the mentioned question (part a) , given parameters are mention as…

Q: A radio system transmits a 2.4GHz signal at 250mW over a distance of 20m through two antennae with a…

A: Answer is given below

Q: B. What is the amount of bandwidth needed to maintain the maximum data rate identified in part A, if…

A: Here in this question we have given a medium of 20khz  or bandwidth =20khz SNR = 10 db. , 20db Find…

Q: 2. (a) A signal travels from BRAC University to your home. At BRAC University, the signal power is…

A: Given: Power at BRAC univeristy=1.2kW = 1.2 * 1000 W =1200 W Power at home =106mW = 106 * 0.001 W…

Q: 3.9. Design a second-order digital bandpass Butterworth filter with a lower cutoff frequency of 1.9…

A: Hi.. As per my company rule i can answer only the first question. So please post next question as…

Q: 2. You have a modem that can operate at a symbol rate of 9,600. Design a modulation system to allow…

A: Answer We need to use a modulation scheme that can transmit multiple bits per symbol i.e., 8PSK…

Q: The transmitter system is shown in Fig. 2, represents transmitting two signals simultaneously by…

A: BELOW ? STEP BY STEP COMPLETE SOLUTION REGARDING YOUR PROBLEM :

Q: c. A telephone subscriber line has a frequency range of 400 Hz and 4400 Hz and a minimum of SNR dB…

A:

Q: The terminal of a computer used to enter alphabetic data is connected to the computer through a…

A: The solution is given in the image below

Q: Q.1/ Fill in the blanks (choose 4): 1. TDM can be extended to the scheme. 2. Delay (latency) is…

A: As per our policy we can only solve the first three questions please post the other questions…

Q: (d) Consider a cable with a bandwidth (H) of 2 MHZ and a signal-to-noise ratio (S/N) of 63. (i)…

A: We need to find maximum bit rate and reason of system fail.

Q: 9.Fiber Optic Cable uses a. Electronic pulses to transmit Information down copper lines b. light…

A: Question 9. Fiber Optic Cable uses a. Electronic pulses to transmit Information down copper lines…

Q: What is the max cable length of STP? a. 100 ft b. 200 ft c. 100 m d. 200 m

A: Question 84. What is the max cable length of STP? a. 100 ft b. 200 ft c. 100 m d. 200 m

Q: When a replacement cable section is spliced into a damaged cable, how should the optical budget…

A: When a replacement cable section is spliced into a damaged cable, how should the optical…

Q: Problem 1 For the following network determine the values of IDI, ID2, and Vo. E = 10V Si -M- +ID…

A:

Transmission media

A communication channel that transmits data from a source to a recipient is referred to as "transmission media." Electromagnetic impulses are used to transmit data. Transmission media's primary purpose is to transmit data in the form of bits via a local area network (LAN). In data transport, it is the physical link that connects the transmitter and receiver. Transmission medium is part of layer 1 or physical layer of the ISO/OSI (Open System Interconnection) model.