15.21 A moving belt line is used to assemble a product whose work content = 22 min. Production rate =35 units/hr, and the proportion uptime = 0.96. The length of each station = 2.0 m and station manninglevel = 1.0 for all stations. The belt speed can be set at any value between 0.6 and 3.0 m/min. It isexpected that the balance delay will be about 0.08 or slightly higher. Time lost for repositioning eachcycle is 6 sec. (a) Determine the number of stations needed on the line. (b) Using a tolerance time that is!!%!50% greater than the cycle time, what would be an appropriate belt speed and spacing between parts?

Answered: 15.21 A moving belt line is used to…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Drivers are trained in a process with two resources. The processing times for the resources are 32 and 140 hours. The first resource has 1 worker and the second resource has 5 workers. Demand occurs at the rate 0.025 Drivers per hour. Instruction: Round your answer to one decimal place. What is the implied utilization (%) of the second resource? %
The cost of computer equipment does not include the consultant's fee to supervise installation of the equipment. True or False
11. You have just determined the actual number of workstations that will be used on an assembly line to be 6 using the assembly-line balancing procedure. The cycle time of the line is 5 minutes, and the sum of all that tasks required on the line is 25 minutes. Which of the following is the correct value for the resulting line's efficiency? Multiple Choice 0.990 0.500 0.973 None of these choices are correct. 0.833
Use MOST to determine the number of TMUs associated with each of the following scenarios: A line supervisor grabs a job order (paper) within reach, walks 10 steps, then lays the order on top of a stack of other orders. The supervisor then returns to her original position. A B G A B P A
A loan processing operation at a local bank processes an average of 7 loans per day. The operation has a design capacity of 10 loans per day and an effective capacity of 8 loans per day. What is the utilization of the processing operation? Select one: a. 100.0% b. 87.5% c. 70.0% d. 80.0% Warranty expense, the cost that a business incurs for the repair or replacement of goods that has sold, is an example of which of the following? Select one: a. Internal failure cost b. Appraisal cost c. Prevention cost d. External failure cost
Suppose for a particular process that the bottleneck cycle time is 54 seconds, and raw processing time is 345 seconds. If there are 4 customers in this system already, and then you walk up and join the line at Station 1, what is your expected lead-time to move through the entire process? Whole number value, no decimals.
DreamInflate is a balloon manufacturing company. Balloon manufacturing consists of seven work stations, each performing a single step as indicated in the table below. There are five workers manned for the seven work stations as shown. Assume the workers are paid $15 per Worker Task Sequence Processing Time (secs/balloon) Task Dye production Electrocharging Dipping (Cold and Hot) Mortar Dipping Balloon inflation and delaltexing Vulcanization Inspection/Testing 1 30 w1 20 3 35 W2 25 W3 30 W4 6. 45 W5 7 40 hour. Each balloon pack is sold for $6 and has a variable cost of $1. The company has fixed costs of $200 per hour. There is more demand than the overall production system can provide. Based on the information provided, answer the following questions: • What is the cost of direct labor for balloons? • How much profit does DreamInflate make every hour? (note that the cost of direct labor is also a variable cost). What would the profit of DreamInflate be if the variable costs were 10…
For a particular process, suppose the bottleneck cycle time is 40, and the raw processing time is 100. What is the minimum number of customers that must be in the system in order for the lead-time (LT) to exceed the raw processing time? Round to one decimal place.
help me with parts b, c, d, e this is all the information the question needs. my question got rejected because the previous expert did not know how to solve this

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS