15. Acid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of 50kN. The elongation of the rod is 1.40Circular mnd that is 600 mm long, and 20 mmnm modutas of clustcity assume that the ratenia dues not yield.A. 68209 GPaB. 0.6821 GPaC. 68.21 GPaD. 682.1 GPa

Answered: Image /qna-images/answer/87d34ef8-1174-46b5-8f32-aa2b71d1053a.jpg

15. id circular rod that is 600 mm long, and 20 mm in diameter is subjected to an axial force of 50kN. The elongation of the rod is 1.40 mne the modules of ukisticity assume that the material does not yield. A. 68209 GPa B. 0.6821 GPa C. 68.21 GPa D. 682,1 GPa

15. id circular rod that is 600 mm long, and 20 mm in diameter is subjected to an axial force of 50kN. The elongation of the rod is 1.40 mne the modules of ukisticity assume that the material does not yield. A. 68209 GPa B. 0.6821 GPa C. 68.21 GPa D. 682,1 GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature.
A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross sectional area of 1cm?; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm? Determine the stress in the rods it p = 6 tonnes.
400mm Find the required spacing of intermediate stiffeners if V*=1600KN 25mm • Check the adequacy of a pair of stiffeners 90mmx12mm • Check the web crushing capacity if the reaction of 1600kN is applied over a stiff bearing length of 250mm at the end of the beam (note that the spread of stress can only go in one direction) • Homework extension: Check the adequacy of an endplate stiffener 300 wide by 16mm thick 12mm Use Grade 300 Steel 1440mm
The masses of the blocks are A=30kg and B=70kg. Between all of the contacting surfaces, μs= 0.10. What is the largest force F that can be applied without causing the blocks to slip?
6. A metallic rod of 500mm length and 50mm diameter, when subjected to a tensile force of 100KN at the ends, experiences an increase in its length by 0.5mm and a reduction in its diameter by 0.015mm. The Poisson's ratio of the rod material is а. 0.2 b. 0.3 С. 0.4 d. 0.5
What is the change in dia.
Asap . Determine the roller support reaction
Solid, copper rod is held stationary at its base and twisted at the top with a torque of 1.0x10° Nm. If the top of the rod rotates 5.0 x 10-2 radians and has a radius of 1.00 m, what is the length of the rod from the bottom to the top? (The shear modulus of copper is 4.6x1010 Pa) 1.5 m O 1.2 m O 2.3 m O 11 m O 3.6 m
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)
278. A rigid horizontal bar of negligible mass is connected to two rods as shown in Fig. P-278. If the system is initially stress-free, determine the temperature change that will cause a tensile stress of 60 MPa in the steel rod. -2 m 2 m 3 m 3 m Bronze A-1200 mm² E 88 GPa x = 18.9 pm/(m. °C) Figure P-278. Steel A = 900 mm? E = 200 GFa Q- - 11.7 m/(m. °C)
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; α = 2.9 × 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; α = 12.5 × 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.2. The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 56 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1).
Q/1/The state of plane stress at a point is shown on the element . Represent this state of stress on an element oriented 15 counterclockwise from the position shown. 30 MPd b’OMIoD‘ go M¥Pa