15 kip The A-36 steel bar shown is made from two segments having cross-sectional areas of AAB = 1-in? and Ag = 2-in?. Determine the following: АВ 4 kip 4 kip B (a) the vertical displacement of end 'A', (b) the displacement of 'B' relative to 'C' and 8 kip 1.5 ft 8 kip (c) the displacement of 'B' relative to 'D'. C 1 ft Answer: a) 8A = 0.0127in b) &B/ = 2.172 * 10-3 in c) 8B/, = 3.1034 * 10-4 in D

15 kip The A-36 steel bar shown is made from two segments having cross-sectional areas of AAB = 1-in? and Ag = 2-in?. Determine the following: АВ 4 kip 4 kip B (a) the vertical displacement of end 'A', (b) the displacement of 'B' relative to 'C' and 8 kip 1.5 ft 8 kip (c) the displacement of 'B' relative to 'D'. C 1 ft Answer: a) 8A = 0.0127in b) &B/ = 2.172 * 10-3 in c) 8B/, = 3.1034 * 10-4 in D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The length of the 2 mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 2 mm exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=200GPA, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D 0.3 m | 20 kg 2 mm 0.3 m 0.1 m
Rigid member ABCD shown here is used to support a 2 kN weight. This member is 6-m-long. Steel (E = 200 GPa) rods BE and CF have a diameter of 0.5 cm and length of 2 m. What is the deflection of point d when the weight is applied? (A) 4.6 mm (B) 2.3 mm (C) 3.8 mm (D) 5.5 mm +x-w
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
A steel beam is subjected to a uniform load with length of 8m. Assume that the beam is simply supported. Use Fy= 248 Mpa. Properties of W-shape beam d=229 mm bf=210 mm rf=23.7 mm Tu-14.50 mm kdes=33. 80mm ry=53.80 mm Ix=113 x 10^6 mm^4 Iy-36.9 x 10^6 mm^4 Sx-990 x 10^3 mm^3 Zx 1150 x 10^3 mm^3 J-2100 x 10^3 mm^4 Cu-387 x 10^9 mm^6 What is the nominal shear strength capacity of the section (in kN)?
A horizontal beam AD is supported by an inclined strut BC carries a load W = 2.4KN at the position shown. The strut, which consist of one bar is connected to the beam by a bolt passing through the three bars meeting at joint C. BC is 75mm wide x 10mm thick strut while AD is 100mm wide by 10mm thick rigid bar. a. Determine the required bolt diameter at A if the allowable bolt shear stress is 68MPA, assuming single shear. b. Determine the total vertical displacement at D if E = 200,000MPa A C 10 10 1.2 B Joint at C 1.2 1.2
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1690 in.*). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 170 kip-ft, P = 30 kips, LAB = 6.1 ft, Lec = 9.2 ft. P MA В C LAB LBC Answer: (a) VA = in. (b) Vg = in.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1860 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 180 kip-ft, P = 12 kips, LAB = 3.8 ft, LBC = 5.7 ft. MA A B LAB LBC Answer: (a) VA = in. (b) VB = in.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm t₁ = 14mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz= 325870000 mm². If the beam will be subjected to a shear force of V=245 kN, determine the shear stress at point H, located at y = 110 mm above the z centroidal axis. d H.V Answer: TH= x Z MPa Уи YK H K
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1640 in.*). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 240 kip-ft, P = 11 kips, LAB = 3.4 ft, Lgc = 5.1 ft. P MA A B C LAB LBC Answer: (a) VA = in. (b) Vg = in.
For the beam shown in the figure determine the following: (EI = constant)a. value of EIθ at Ab. value of EIθ at Cc. value of EIδ at Bd. value of EIδ at D
*2-92. Express each of the forces in Cartesian vector form and determine the magnitude and coordinate direction angles of the resultant force. 0.75 m FAS FAS = 250 N FAC = 400 N 3 m 40 2 m im- -1m- Ргob. 2-92