(15) A 150mm pulley is mounted to the motor 100mm from the bearing. The motor is 20kW & rotates @ 640rpm. The belt wraps the pulley @ 170°. The net belt tension is acting as transverse load on the shaft. Determine the combine stress on the shaft.

(15) A 150mm pulley is mounted to the motor 100mm from the bearing. The motor is 20kW & rotates @ 640rpm. The belt wraps the pulley @ 170°. The net belt tension is acting as transverse load on the shaft. Determine the combine stress on the shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

(14) A 40mm steel shaft rotates @ 600rpm & handles 10kW delivered from a pulley located 300mm from one side of the bearing. The shaft is supported by bearing 800mm apart. Assume that force acting on the shaft is the equal to the maximum belt pull. Determine the maximum combined stress of the shaft.
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
QUA four stroke internal combustion engine has the following specifications: Brake power 7.5 kW; Speed 1000 r.p.m.; Indicated mean effective pressure 0.35 N/mm2; Maximum gas pressure 3.5 N/mm2; Mechanical efficiency - 80 %. Determine: 1. The dimesions of the cylinder, if the length of stroke is 1.4 times the bore of the cylinder: 2. Wall thickness of the cylinder, if the hoop stress is 35 MPa: 3. Thickness of the cylinder head and the size of studs when the permissible stresses for the cylinder head and stud materials are 45 MPa and 65 MPa respectively. Any other data required for the design may be assumed.
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5. Q3 a) An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N- m. Assuming that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowableshear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively.
A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. It is press fit on a solid shaft of same material with diameter 42mm such that the nominal diameter between sleeve and shaft became 41mm. a. Find the pressure developed between shaft and sleeve. b. Draw the tangential, radial, and total stress as a function of radius, for both sleeve and shaft. c. Find the maximum shaft diameter that can be used before failure.
A driveshaft for a milling machine transmits 15.0 hp at a speed of 240 rpm. Compute the tor- sional shear stress in the shaft if it is solid with a diameter of 1.44 in. Would the shaft be safe if the torque is applied with shock and it is made from SAE 4140 OQT 1300 steel? 447.
A pulley is keyed to a 56.8mm diameter shaft by a 7/16 in x 3 in flat key. The shaft rotates at 697 rpm. The allowable compressive stress for the key, hub and shaft are 66 ksi. 59 ksi and 72 ksi, respectively. Determine the maximum torque, in lb-in, the pulley can safety deliver. Express your answer in 3 decimal places.
Help me answer this thanks!
The shaft whose torque varies from 2100- 6000 in- lbs has 1 and one- half inch diameter and 60000 psi yield strength . Compute the shaft variable component stress.
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
The cylinder of a four stroke diesel engine has the followin, specifications : Cylinder bore :150 mm Maximum pressure : 3.5 MPa Cylinder material : GCI FG200 Factor of safety : 6 Poisson's ratio : 0.25 Determine the thickness of the cylinder wall. Also calculate the apparent and net circumferential stresses in the cylinder wall.