14.9 In Figure 14.13a, let H = 6 m, y = 16.5 kN/m², o' = 30°,8' = 20°, c' = 0, a = 10°, and ẞ = 80°. Determine theCoulomb's active force per meter length of the wall and thelocation and direction of the resultant force.

Pa = 201. 366 kN/m^2Location = 2mDirection = Pa acts at angle 20 degrees

Answered: 14.9 In Figure 14.13a, let H = 6 m, y =…

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter14: Lateral Earth Pressure

Section: Chapter Questions

Problem 14.5P

See similar textbooks

Question

100%

14.9 In Figure 14.13a, let H = 6 m, y = 16.5 kN/m², o' = 30°,
8' = 20°, c' = 0, a = 10°, and ẞ = 80°. Determine the
Coulomb's active force per meter length of the wall and the
location and direction of the resultant force.

Expert Solution

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

2 Points Question 14 of 15 The cross-sectional area of a column is in the shape of two concentric circles whose outer diameter is 200 mm. If it is to be subjected to a force of 75 kN, find the thickness of the wall if the ultimate stress capacity is 32 MPa. Use FS = 3.2 Select the correct response: 12.57 mm 17.75 mm 12.75 mm 15.75 mm rs ion
Q2/ A cylindrical barrier holds water, as shown in Fig.1, the contact between cylinder and the wall is smooth. Consider a Im length of cylinder, determine the weight of the cylinder and the force exerted against the wall, take y, = 9790 N/m³. Fig. 1 TIL ... r-2m
4.144 The tube shown has a uniform wall thickness of 12 mm. For the 170110 S loading given, determine (a) the stress at points A and B, (b) the point where the neutral axis intersects line ABD. ne-601 la archy siques of bat Fig. P4.144 D F H E 28 kN 14 kN 28 KN 125 mm. 75 mm 1 A 025.0 40137
Segment AB of the bar is a tube with an outer diameter of 1.5 in. and a wall thickness of 0.125 in. Segment BC is a solid rod of diameter 0.75 in. Determine the normal stress in each segment.
O. No 7: The cross section of the beam has a uniform wall thickness. Analyze using concepts of shear stress, shear flow and shear centre in thin walled open section beams to determine the location of the shear center relative to point B. 6 in. 6 in. 3 in. 01 in. 3 in NA 3in. Figure Q. No. 7
The simply supported beam AB as shown in Figure Q3(a) has a uniform load of intensity, w=15 kN/m acts throughout the entire length of the beam. The cross-section of the beam is shown in Figure Q3(b). Given the second moment of area, INA = 36 x 106 mm“. (a) Determine the shear stress at the top of the hole at section a-a. (b) Determine the maximum shear stress at point M and N based on the maximum shear force. (c) Calculate the absolute maximum shear stress of the beam. 0.6 m 1.8 m a. w = 15 kN/m В Figure Q3 (a) 160 Ø30 hole 110 NA * 70 M y = 80 40 N 100 All dimensions in mm
Please answer all, Strength of Materials. Thanks!
Consider the retaming wall shown m the ligure below Calculate the Rankine passive force per unit length of the wall and the location of the line of action of that resultant at which it acts on the retaming wall. 15.72KN/m3 1=30 C1=0 WT sat%3D15.72KN/m3 112=26 C1=10KN/m2
Determine the outside diameter of a hollow steel rod that will carry atensile load of 55,000 kg at a stress of 1,500 kg/cm2 and the wallthickness is 10 mm.A. 8.17 cm C. 12.67 cmB. 8.34 cm D. 7.28 cm
5.2.2 The thin-walled tube is used as a beam to support the uniformly distributed load of intensity w0. (a) Find the largest allowable value of w0 based on the allowable stress in bending of 100 MPa. (b) Compute the corresponding maximum shear stress in the beam.
Tall open top stand pipe.
e9

SEE MORE QUESTIONS

Recommended textbooks for you

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning