14.1 through 14.8 Determine the reactions and draw the shear and bending moment diagrams for the beams shown in Figs. P14.1 through P14.8 using the three-moment equation. 100 kN 10 kN/m A 12 m 6 m 21 E = constant FIG. P14.5, P14.12

Q: Problem 1.8. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown in…

A: Here we will draw a separate free body diagram of each section.Using the formula of stress and…

Q: The uniform, 20-kg bar is placed between two vertical surfaces. Assuming sufficient friction at A to…

A: The following information has been provided to usThe uniform 20-kg bar that is placed between two…

Q: A uniform beam of arbitrary unsymmetrical cross section and length 2L is built-in at one end and is…

A: Given data in question  Propped cantilever  Span member length Point load W To find out  Reaction…

Q: page Wire is being drawn at a constant rate from a spool by applying a vertical force P to the wire…

A:

Q: Problem 8.8 Draw the influence lines for vertical reactions at supports Band D and the shear and…

A:

Q: SOLVE ALL EXTERNAT SUPPORT REACTIONS FOR THE BEAMS SHOWN +y 20 kN/m 10 kN A B tx C 4m 4m + 2m--|

A: To find external support reaction

Q: For the beam shown in Fig. I, determine the reactions at all supports using the method of moment…

A: For the beam shown in Fig. I, determine the reactions at all supports using the method of moment…

Q: M (KN.m) w (kN/m) P (kN) P (kN) P (kN) B A ,2m, 2 m, 2 m, 3m , 3 m , 3 m Find the magnitudes of the…

A: let,RA=vertical reaction at support A in upward directionRB=vertical reaction at support B in upward…

Q: • Determine the member end moments and reactions for the 2 k/ft B. 100 k ft 15 ft El = constant…

A: To find Member end moment and reaction for the frames.

Q: Influence lines for the beam for this figure below

A: Step 1:Step 2:

Q: 50 kN 6.25 kN/m By В 2,5 m 2.5 m 4 m

A:

Q: w (kN/m) w (kN/m) P (kN) P (kN) P (kN) 3 m 3 m, 2 m, Find the magnitudes of the support reactions at…

A: w = 5 Kn/m P = 13 Kn

Q: Figure 1 shows a frame that is fixed at E. As indicated in the Figure, the frame is exposed to two…

A:

Q: Sketch the shear force diagram for the beam loaded shown in Fig. Q1 by obtaining the shear force…

A:

Q: 8.1 Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A: 1. Calculate the Normal Force (N):  The normal force is the perpendicular force exerted by the…

Q: 8.5 Knowing that = 45°, determine the range of values of P for which equilibrium is maintained. 800…

A: To determine the range of values of P  for which equilibrium is maintained in this system, we need…

Q: 18 kN/m A 12 m 8 m El = constant E = 200 GPa I = 476(10°) mm FIG. P16.4, P16.7

A: Determine the reactions and draw the shear and bending moment diagrams for the beams shown in Figs.…

Q: Determine the member end moments and reactions for the frames P16.18 - P16.20

A:

Q: Determine the resultant of the force system shown & y intercepts. Y 300)

A:

Q: degree of indeterminacy and stability

A: Given: The frame structures with storey To find: The indeterminacy and stability

Q: Question 1 Given the frame in Figure 1 below. Do the following: 1.1 Calculate the reactions at A and…

A: Use moment distribution method , Determine stiffness of each member, KAD = 3EIL=3EI4 KGE  =…

Q: Determine the reactions and draw the shear and bending moment diagram of fig 16.5 by using…

A: The compression strength means the material or structure's ability to resist loads that tend to…

Q: Draw influence lines for the reactions at A and C and for the bending moment at E in the beam system…

A: Solution-

Q: Q1) The plate in Fig. 1-18 rests on top of the thin film of water, which is at a temperature of…

A: Finding out shear stress.

Q: Determine the joint displacements, member axial forces, and support reactions for the Baltimore…

A: Support Reactions :  Due to symmetry in truss system as well as loading,R1 = R9 = 120×72 = 420 kN

Q: F1 y 300 300 R 400 F3+ X- 400 THON EXAMI F2 Fig. SSDH 55.56

A:

Q: In Fig. 3, support A is fixed while support B is roller. Use consistent deformation method to find…

A:

Q: 8.107 The coefficient of static friction between block B and the horizontal surface and between the…

A: We have to find the smallest mast mass f bloock B foor equillibrium condition.

Q: 15 KN 30, kN 30 kN 40 ,KN 40, kN 20, kN 20 m 30 m B 6 8 20 m = 120 m Fig. P4.9

A:

Q: 2. A uniform live load with an intensity of 25kN/m and length 10m is placed on a simply supported…

A: Load intensity of moving load = 25kN/m, and length= 10m  We have to find out the followings:  ILD…

Q: 240 lb H=0.35 Mk=0.25 Fig. P8.1 and P8.2 8.2 Determine whether the block shown is in equilibrium and…

A:

Q: 4.75 The structure consists of two identical bars joined by a pin at B. Neglecting the weights of…

A: The moment at pin support is zero.Acceleration due to gravity is 9.81 m/s2The frame is statically…

Q: B ,2 m, 2 m, 2 m, 3m , 3 m, 3m Find the magnitudes of the support reactions at A, B and C for the…

A:

Q: Determine the member end moments and reactions for the frame shown in Fig. 15.18(a) by the…

A:

Q: 75 k 2 k/ft D B 5 ft 30 ft 31 E = constant

A:

Q: 1. Determine the joint displacements, member axial forces, and support reactions for the Baltimore…

A: Figure of a Bridge truss We need to calculate support reactions, member axial forces and joint…

Q: Two tugboats are towing a Cargo ship as shown in Fig.1. Tugboat A exerts a force of 15OON at 30°…

A: - Taking equilibrium condition of forces in horizontal direction. we get,…

Q: Q2 The cross-sectional dimensions of a beam are shown in Fig. P8.12. The internal bending moment…

A:

Q: What is the reaction at C in kips. In Figs. P14.1–P14.4 using the method of consistent deformations.…

A:

Q: 13.4 Determine the reactions and draw the shear and bending moment diagrams for the beams shown in…

A: