14. a total current of 60 A is divided among 3 parallel branches having resistances of 10, 6, and 12 ohms respectively. What is the current that flows through the branch with 10 ohms resistance? a. 17.1 A с. 14.3 А b. 28.6 A d. 42. 9 A

14. a total current of 60 A is divided among 3 parallel branches having resistances of 10, 6, and 12 ohms respectively. What is the current that flows through the branch with 10 ohms resistance? a. 17.1 A с. 14.3 А b. 28.6 A d. 42. 9 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Discuss how the circuit works
Using the nodal point method in the circuit shown in the figure. calculate the currents passing through the resistors of 3 and 6 ghms and the curent passing through the branch where the 16V şQurce is located. 50 16 V 24 V
Part 3 please solve it
which has a coss-seutional asea of 300m. gratn csuust oosuts of a tast steelyote GNich has a co035-seotonal asea of 300mm mian length of 140 mm. hest ane 2 aligaps, 14ch 0 25mn long. Lalulate (a) thu m mt srquire d to producta flux of 0 06 m wb in thu argaps 6) the valuu of thes salative hreabity f cast sterel at this flux density The magnetisat ion rusue for castster is given by the following B(T) 01 0.20.3 0 4 4(A/M) 170 300 380 460
1. Given the DC Series Circuit below: R₁ = 30 kr m E=IVE M R₂ = 15k^ Mu R₂ = 60kλ a) Draw the DC Series Equivalent Circuit and use it to find the total current, IT. b) What are the currents, I1, I2 and 13? c) Find the voltages V1, V2 and V3 by using Ohm's Law. d) Find the voltages V1, V2 and V3 by using Voltage Divider Rule. e) Calculate the Total Power, PT dissipated in this circuit. f) Compute the power dissipated by each resistor, P1, P2 and P3.
In the figure below, the Load resistance R_L has a value of 15 ohms. Determine the magnitudes of the current (A) flowing through the 10-ohm resistor, the voltage (V) across the Load and the power (W) dissipated in the 6-ohm resistor. 24 V R. 1A 10A Power 6-ohm resistor(W) Choose.. Current through 10-ohm resistor(A) Choose.. Voltage across the Load resistor (V) Choose.. +
Electrical Engineering - Power System Analysis Please solve the question on the word
4. Discuss how the circuit works
I don't want numbers or complete solution just explain to me how i can solve 5 and 6 in B the steups for solution and the equations
1. A 50-ohm, a 90-ohm and an unknown value resistor are in series across a 60-V generator with 1/3A flowing through it. What is the resistance of the unknown value resistor? a. 10 ohms b. 30 ohms c. 20 ohms d. 40 ohms 2. A 6-V mobile receiver draws 36-W. It is to operate from a 12-V battery, what value resistor must be used in series with it to maintain the 36-W receiver dissipation? a. 8 ohms b. 2 ohms c. 4 ohms d. 1 ohm 3. A 40-ohm resistor and a 60-ohm resistor are in parallel. In series with them are two other resistors of 20-ohm and 30-ohm. The whole combination is connected across a 1.5-V dry cell. What is the current in the 60-ohm resistor? a. 12.162 mA b. 30 mA c. 8.108 mA d. 20.27 mA 4. A 40-ohm resistor and a 60-ohm resistor are in parallel. In series with them are two other resistors of 20-ohm and 30-ohm. The whole combination is connected across a 1.5-V dry cell. What is the current in the dry cell? a. 8.108 mA…
2. Frame a priority list for supplying a load up to 2000 Mw in the given power plants Plant J: Fl = (2 + 0.003 PI) 103 k-cal/Mw-hr. P1= 500 MW Plant 2: F2 = (6.5 + 0.006 P2) 103 k-cal/Mw-hr P2 max = 300 MW Plant 3: F3 = (6 + 0.005 P3) 103 k-cal/Mw-hr P3 max = 240 MW The fuel costs at the plants are given by CP I=0.92 RO/kcal CP2 = 1.05 RO/kcal CP3 = 1.2 RO/kcal
Please help with 1 and 2 1.Use kirchhoff's laws to determine the current 2. Determine the power supplied by the dependent source. Use voltage division