14. A single-phase AC supply has ac mains voltage of 230 V at 50Hz and feeder (source) impedance of 1.0 and 3.0 ohms inductive reactance after which a load of 5.2 kVA, 0.8 pf lagging is connected. voltage drop across the source impedance and (b) the voltage across the load. If a PWM based DST raise the voltage to same as input voltage (230V), calculate (c) the voltage rating of the DSTATCOM, of the compensator, and (e) the current rating of the compensator. Zs=1+13.0 000m į 16 4KVA, 0.8 lagging DSTATCO M 2000 23 23 ell

14. A single-phase AC supply has ac mains voltage of 230 V at 50Hz and feeder (source) impedance of 1.0 and 3.0 ohms inductive reactance after which a load of 5.2 kVA, 0.8 pf lagging is connected. voltage drop across the source impedance and (b) the voltage across the load. If a PWM based DST raise the voltage to same as input voltage (230V), calculate (c) the voltage rating of the DSTATCOM, of the compensator, and (e) the current rating of the compensator. Zs=1+13.0 000m į 16 4KVA, 0.8 lagging DSTATCO M 2000 23 23 ell

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2- Draw and explain the phasor diagram for two transformers in parallel.
Subject name: Power System Protection
Subject - Design electrical circuits for single-phase AC networks Question - Compare the effect of varying resistance, capacitance and inductance in parallel and series AC circuits on voltage, resistance and impedance
A series resistance – capacitance (R – C) circuit is connected to 230 – volt, 50 cycle AC source. The current through the resistor is 45.45 A and the power taken by the circuit is 5,000 watts. Compute the following: 1.) Power factor angle 2.) Circuit impedance 3.) Ohmic value of the resistor
A low voltage distribution transformer feeds two different loads with a three-phase line. The nominal voltage of the line is 400 Volt. The total length of the feeder is 500 m. The distance from the transformer to these loads is 140 m and 340 m, respectively. Their consumption is 11 kVA with a 0.8 lagging power factor and 10 kW with a 0.8 lagging power factor, respectively. The feeder's cross-section is 15 mm2 and the feeder's conductivity is 56 m/ohm.mm2. Find the following information. The distance from the transformer to the maximum voltage drop point is m The maximum voltage drop is Volt The power loss between the transformer and 11 kVA load is Watt.
Three single phase transformers each having a 240 V primary and two 250 V secondaries, as shown in the figure below, is to be connected to a 400 V, 3–phase supply to give a six phase output. A d e В f Show how this is done and find the voltage between adjacent phases of the 6-phase output.
For the same alternator the ratio of rated kva, when connected as a three phase winding alternator to when connected as a single phase alternator by using all the coils is
No-load operation and short circuit tests were performed on three-phase, 50 Hz 480/220 delta / Y connected transformer. In these testsThe line voltage, line current and three-phase total power have been measured from the high voltage windings and the test results are below.pictures. 100 A DC current when 1.08 V DC voltage from non-transferable software is applied to the low voltage windingshas attracted.Find the single phase equivalent circuit parameters of this transformer.idle test:Voltage: 480V Power:114w current: 0.71Ashort circiut test:V: 10v P: 78w c: 18.3a
Ql-phase step down transformer 1250 KVA, 10002200 V, 50 Hz The resistance /phase and leakage reactanceiphase of the primary winding are 0.78 2 and 4.82 and the corresponding values for the secondary winding are 0.012 and 0.002 respectively if the primary winding is connected in delta and secondary in star calculate: )The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited li) The full load copper loss
2. Given three identical ideal single-phase transformers with each rated at 100KVA and 7kV/3.5kV, they are connected as a three-phase transformer bank. The three-phase transformer has high voltage side connected in delta and the low voltage side is connected in wye. A three-phase 200KVA, wye connected load is connected at the low voltage side of the transformer. Calculate the following: a. Rated line-to-line voltage on each side b. Line current on each side of the transformer
What is the average power in ghe single phase ac circuit with the purely resistive load? It is sinusoidal steady state excitation.
Q4/ What is the three phase emf generation and show their two main advantages with type of connection in three phase circuit.