Prob. 1, 2, 3.13.13 through 13.15 A retaining wall is shown in Figure 13.37. For each problem,determine the Rankine active force, P.r per unit length of the wall and the locationof the resultant.ProblemHH,Y2o' (deg) o' (deg)13.134.3 m 2.1 m16.2 kN/m 19.9 kN/m³282819.1 kN/m12 kN/m?21 kN/m²13.147.3 m 3 m18 kN/m?323213.159 m16.5 kN/m 20.2 kN/m³4 m3034Surcharge = qSandcj = 0Groundwater tableHSandY2 (saturated unit weight)cz = 0Frictionless wallFigure 13.37Cengage Learning 2014© Cengage Leaming 2014

Solution 13.13:- If the cohesion is zero σ'a=Ka×σ'v For the top soil layer and for bottom layer,…

13.13 through 13.15 A retaining wall is shown in Figure 13.37. For each problem, determine the Rankine active force, Pa» per unit length of the wall and the location of the resultant. Problem H H, Y2 Ф (deg) ф (deg) 13.13 4.3 m 2.1 m 16.2 kN/m 19.9 kN/m 28 28

13.13 through 13.15 A retaining wall is shown in Figure 13.37. For each problem, determine the Rankine active force, Pa» per unit length of the wall and the location of the resultant. Problem H H, Y2 Ф (deg) ф (deg) 13.13 4.3 m 2.1 m 16.2 kN/m 19.9 kN/m 28 28

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7.17 A soil profile consists of a clay layer underlain by a sand layer, as shown in Figure P7.17. If a tube is inserted into the bottom sand layer and the water level rises to 1 m above the ground surface, determine the vertical effec- tive stresses and porewater pressures at A, B, and C. If K, is 0.5, determine the lateral effective and lateral total stresses at A, B, and C. What is the value of the pore- water pressure at A to cause the vertical effective stress there to be zero? GWL 11 m Y=18.5 kN/m? Clay 2 m Y= 19.0 kN/m³ 2: 1,5m Y =17.0 kN/m Sand 2 m FIGURE P7.17
Q 11.7
5. A 13-m-high, 7-m-wide rectangular plate blocks the end of a 12m-deep freshwater channel, as shown in the figure. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate by the ridge. I'm 12 m
UPVOTE WILL BE GIVEN. WRITE THE COMOLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. BOX THE FINAL ANSWER.
The retaining wall shown above is subjected to an active earth pressure distribution as illustrsted in the figure. What is the eccentricity of the resultant load acting on this wall (measured from the centre of the wall)? XX w=240 kN/m 5m length W 2m 35 kPa O 0.31 m O 0.61 m O 0.23 m O 0.41 m
A shear force of V = 2.6 kips acts on the thin-walled section. Using dimensions of a = 3 in., b = 5 in., h = 6 in., and t = 0.35 in. (where t is constant throughout the entire cross section), determine the shear flow magnitude at points A, B, and C. %3D A N.A. г (tур.) a Answers: 114.031 Ib/in. 9A = 9B = 228.063 Ib/in. 9c = 206.708 Ib/in.
Kindly show the solutions for the following shear values shown in the diagram. Show the Complete solution.
Q5: In the case of the retaining wall depicted below. Calculate the lateral earth fore at rest per unit length of the wall. Determine the location of the resulting force as well as its magnitude. [25] y = 16.5 kN/m $ = 30 C = 0 Ground v Water table 2.5m Yur = 19.3 kN/m 0 = 30 C = 0 2.5m Good Luck
12.3 Refer to Figure 12.12a. Given: H = 4 m, y = 16.5 kN/m³, ' = 30°, c' = 0, and B = 85°. Determine the Coulomb's active force per meter length of the wall and the location and direction of the resultant for the following cases: a. a 10° and 8' = 20° b. a = 20° and 8' = 15°
Determine the magnitude (kN) and location (m) of the resultant passive force on the 30m long wall.
The channel section shown in Figure P9.65 is subjected to a vertical shear force of V = 7 kips. Calculate the horizontal shear stress TA at point A, and the vertical shear stress TB at point B. 2 in. 0.25 in. B 3 in. 0.20 in. -0.20 in. 8 in. FIGURE P9.65
For the frictionless wall shown in Figure No 1, Calculate the following: (a) The active lateral earth pressure distribution with depth.  (b) The passive lateral earth pressure distribution with depth(c) The magnitudes and locations of the active and passive forces.  (d) The resultant force and its location.  (e) The ratio of passive moment to active moment. Note: UDL should be considered as mentioned in the figure