(13) For a certain polyphase induction motor, which at full load operates at itsmaximum power factor, the starting current and the no-load current at full voltageexceeding the full-load value. What would be the power factor and slip at full-loadreduction in voltage which would just permit stable operation at a torque notAssuming the rotor and stator copper losses are equal, determine the percentageare in the ratio of 10/1 and the power factor in each case is 0-25.torque with the voltage thus reduced?

A polyphase induction motor is made up of a conductive squirrel-cage embedded in a laminated rotor…

(13) For a certain polyphase induction motor, which at full load operates at its maximum power factor, the starting current and the no-load current at full voltage reduction in voltage which would just permit stable operation at a torque not Assuming the rotor and stator copper losses are equal, determine the percentage Exceeding the full-load value, What would be the power factor and slip at full-load are in the ratio of 10/1 and the power factor in each case is 0-25. torque with the voltage thus reduced?

(13) For a certain polyphase induction motor, which at full load operates at its maximum power factor, the starting current and the no-load current at full voltage reduction in voltage which would just permit stable operation at a torque not Assuming the rotor and stator copper losses are equal, determine the percentage Exceeding the full-load value, What would be the power factor and slip at full-load are in the ratio of 10/1 and the power factor in each case is 0-25. torque with the voltage thus reduced?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3 phase , 6 pole , 400 V , 50 Hz , induction motor has R2= 0.1 ohm /ph , X2= 0.8 ohm /ph and the induced emf between slip rings at standstill is 160 V , Assume the friction losses is 300 W. find :- a) the torque output at slip =3% . b) critical slip and the torque maximum .
A 400 V, 3-phase, 4 pole slip ring induction motor is supplied at rated voltage and frequency. The actual rotor resistance per phase is 3 2 and the stand still rotor reactance per phase is 12 2. Neglect stator resistance, reactance and magnetizing reactance. 1. Determine the value of resistance to be added to the rotor circuit to get the maximum torque at starting. 2. Determine the value of resistance to be added to the rotor circuit to get 75% of the maximum torque at starting.
Q2: A single-phase induction motor with a 4-pole, 50-Hz, 130-V, is rotating in the clockwise direction at a speed of 1450 rpm. Determine its per-unit slip (a) in the direction of rotation and (b) in the opposite direction. At standstill the rotor resistance is 15 Q, determine the effective rotor resistance in each branch.
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
22. A) Why is the power factor of a lightly loaded 3-phase squirrel-cage induction motor very low? a) most of the power supplied to the motor at light loads is magnetization or inductive power b) most of the power supplied to the motor at light loads is resistive power c) most of the power supplied to the motor at light loads is capacitive power d) none of the above B) What happens to the power factor as load is increased on the motor? a) the power factor increases b) the power factor deceases c) remains the same
When the speed of the dc motor is varied by changing the armature resistance, is to be held constant. O field flux O applied voltage O load current O armature current The starting torque of a three phase slip ring induction motor is to a three phase squirrel cage induction motor. when compared O very low O low same O high
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
1. The rotor resistance and reactance per phase of a three-phase wound rotor induction motor are 0.035 and 0.15 ohm respectively. If an additional resistance is added, the starting torque is one half of maximum torque and the full load torque is three-fourth of the maximum. Determine the following: a. Full load speed b. speed at maximum torque c. value of additional resistance per required to achieve these conditions.
On full load, a 300 V series motor takes 90A and runs at 15 rev/s. The armature resistance is 0.1 ohm, and the series winding resistance is 50 mohm. Determine the speed when developing full load torque but with a 0.2-0hm diverter parallel to the field winding. (Assume that the flux is proportional to the field current.