*13-12. A pressure-vessel head is fabricated by weldingthe circular plate to the end of the vessel as shown. If thevessel sustains an internal pressure of 450 kPa, determinethe average shear stress in the weld and the state of stress inthe wall of the vessel.-430 mm -=10 mm20 mm

Average shear stress by taking the vertical forces is π4501000×22×450×103=τa2π4502101000τa=5.06 MPa…

Answered: *13-12. A pressure-vessel head is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC, determine the diameter of cable AB so that the average normal stress in this cable is the same as in the 10-mm-diameter cable AC. 43
The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 700 mm and a wall thickness of 8.9 mm. For a gage pressure of 1.27 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume = 51. s Answers: (a) Normal stress= (b) Shear stress - MPa MPa
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb/ft2, determine the state of stress at points Cand D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe. 6 ft 3 ft 上 A B x 12 ft 150 lb/ft²
An axial load is applied to the rectangular cross section bar which is welded at the 57 degree angle shown. If the weld material has a failure normal stress of 160 mPa and a failure shear stress of 90 mPa, determine the required thickness if a factor of safety of 2.3 is required. Also determine the required diameter of the bolts(to the nearest mm) if the plate is face bolted to the supports. The bolt material has a failure shear stress of 175 mPa.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 3.10 ksi.
The piston-cylinder assembly above has a wall thickness of 0.125" and an outer radius ro= 2 in. If the internal gauge pressure is 1.2 ksi, determine the maximum normal stress in the piston wall. 18 ksl O9 ksi 36 ksi N/A (this does not meet the criteria of a "thin-walled" pressure vessel)

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

*13-12. A pressure-vessel head is fabricated by welding the circular plate to the end of the vessel as shown. If the vessel sustains an internal pressure of 450 kPa, determine the average shear stress in the weld and the state of stress in the wall of the vessel. -430 mm - =10 mm 20 mm