13-10. A wood pipe having an inner diameter of 0.9m0.9is bound together using steel hoops each having a cross-sectional area of 125 mm. If the allowable stress for thehoops is o = 84 MPa, determine their maximum spacings along the section of pipe so that the pipe can resist an in-ternal gauge pressure of 28 kPa. Assume cach hoop supportsthe pressure loading acting along the length s of the pipe.28 kPa28 kPa

Given that, Consider the diagram showing below,

Answered: 13-10. A wood pipe having an inner…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QI/ For the assembly below, determine the average normal stress for the cable. Assume that the cable has a diameter of 10 mm. take P =12 kN. 0.5 m -0.75 m -0.75 m 0.75 m
The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is subjected to an internal pressure of 500 psi and the axial tension and torsional loadings shown, determine the principal stress at a point on the surface of the pipe.
The steel bracket below is used to connect the ends of two cables. If the applied force P=1.50kip, determine the maximum normal stress (in ksi) in the bracket. Assume the bracket is made from a rod having a diameter 1.5in.
The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial distributed loading along its length of w= 8 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.9 m. Assume a = 0.6 m and b = 1.0 m. B MPa a Answer: 0 = i b
The steel bracket is used to connect the ends of two cables Part A O max = If the applied force P= 1 kip, determine the maximum normal stress in the bracket Assume the bracket is a rod having a diameter of 2.25 in Express your answer to three significant figures and include appropriate units. Value Units 4 in. ? P
The sign is supported by a hollow structural tube of 15 in. outer diameter and 0.5 in. wall thickness. Given the weight and the design 3ft wind loading both acting at the center of the sign, determine the state of stress at points a and 6. Write cach state of stress in the form of a tensor, olserving the r-y-z coordinate system shown, and sketeh the stresses acting on a differential element at each point. s kips 3 kips 3 ft 3ft
A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E = 10750 psi and v=0.46, determine the stresses in the balloon. Assume the stress-strain behavior is linear. Answer: 0 = i ksi
O d. NA = 0.374 , Ng = 2.611 Clear my choice The pipe assembly shown is subjected to a force F = 12 kN and P = 6 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. 1.2 m 0.65 m d= 176 mnm D- 200 mm Cross section Select one: O a. NH =4.07 360=5355 Od.N-8576 solid rounc bar deep wich a 2 5-mm radiu 1:14 AM fla )) ENG 22/4/2021
8–67. The metal link is subjected to the axial force of P=7 kN. Its original cross section is to be altered by cutting a circular groove into one side. Determine the distance a the groove can penetrate into the cross section so that the tensile stress does not exceed oallow better way to remove this depth of material from the cross section and calculate the tensile stress for this case. Neglect 175 MPа. Offer a the effects of stress concentration. P. 40 mm P 40 mm 25 mm Prob. 8–67
Determine the average normal and shear stresses at a cross section (a-a) for e-65°. The member has a square cross section with side b= 20 mm. F- 2kN b- 20 mm
The 520-kg engine is suspended from the jib crane at the position shown. Determine the state of stress at point B on the cross section of the boom at section a -a. Point B is just above the bottom flange. (Figure 1) Figure 2m 2m 2m- 4 MP A D 0.4 m 150 mm 150 mm . Determine the normal stress at point B Express your answer using three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. Submit μA B = 3.85 Units You have already submitted this answer. Enter a new answer No credit lost. Try again. TB = n → Previous Answers Request Answer Submit Determine the shear stress at point B. Express your answer to three significant figures and include the appropriate units. HA ? Value Request Answer Ć Units P ?
Determine the shortest distance d to the edge of the plate at which the force P can be applied so that it produces no compressive stresses in the plate at section a–a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS