12.61 A fixed amount of air initially at 50°C, 1 atm, and 20% relative humidity is cooled at constant pressure to 23°C. Using there the psychrometric chart, determine whether condensation occurs. If so, evaluate the amount of water condensed, in kg per kg of dry air. If there is no condensation, determine the relative humidity at the final state.

Q: Research and investigate the various technologies employed and membrane systems  for various modes…

A: Describe about Membrane separation-Various technologies employed and membrane systems for various…

Q: What are fluidised or moving-bed adsorbers?

A: Adsorption is a separation process in which the solute from the fluid is separated by adsorbing on…

Q: Draw a flow diagram of life cycle of glass/ceramic industry.

A:

Q: Use equations and words to describe how stirring a solution will affect the mass-transport limited…

A: The current that flows through a solution at any time is a direct measure of the rate of the…

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: What is the difference between the Murphree tray and point efficiencies?

A: Murphree tray efficiency and the point efficiency is to be differentiate.

Q: What is the difference between truncation error and stability?

A: To understand the answer to this problem knowledge of Process control systems is required. The given…

Q: Mention some key considerations during installation of a cyclone seperator?

A: Cyclonic separation is a means of separating different liquid phases, or, separating particles from…

Q: Explain RECYCLE AND BYPASS?

A: To design a new process or analyze the existing one, material balance, energy balance equations at…

Q: Explain Semibatch process?

A: In a batch process, the desired product comes out of the reactor in groups i.e. in discrete amounts…

Q: What are the Safety inspections. [Important exams, checklist, and inspections] for diaphragm pump?

A: The safety inspections for the diaphragm pump are to be mentioned.

Q: Given a 35% mixture, what will be the time of flow? * O 43.5% O 41.5% O 6.6% 6.5%

A:

Q: Illustrate and discuss the process flow for the manufacture of porcelain

A: Solution-Step:  (a) Component needed(i) Feldspars K2O.Al2O3.6SiO2 & Na2O.Al2O3.6SiO2(ii) Quartz…

Q: The centrifugal pump is most widely used in the chemical industry. Sketch the internal structure and…

A: Introduction A centrifugal pump converts rotational energy, often from a motor, to energy in a…

Q: Should axial despersion be avoided?

A: It is to be stated whether axial dispersion should be avoided or not.

Q: Describe five main parameters that govern the performance of the polymer production process. Provide…

A: Polymer manufacture is a complex process governed by numerous aspects that affect the final…

Q: In the plate and frame filter press, by plotting the filtrate volume as a function of time per…

A:

Q: Write the mobile and stationary phases in gas chromatography. What is the physical state of the…

A: Chromatography is a physical technique that finds application in the separation, identification, and…

Q: 1. Explain in detail how grain size affects the strength of a metal alloy.

A: The grain size of a metal alloy significantly affects its strength due to the influence of grain…

Q: Process flow scheme on how to make tempered glass

A: There are two types of commercial glass based on the process of their manufacture. These are:…

Q: ne test tube. A glapi OI tms aCtivit LIms 2 13 31 Time (seconds)

A: The order of the temperatures is to be arranged as per the graph given.

Q: Define reflux ratio. Also give the four information (data) required to detennine the number of…

A: Definition:- Reflux ratio (R) is defined as the amount of liquid (L) that is returned to the column…

Q: Calculate the following: Thermal conductivity of brass Calculated quantities Value Difference in…

A: Hi, thank you for posting the question. According to our guidelines, we are allowed to answer only…

Q: Mention the steps that are helpful in performing material and energy balance calculations.

A: Material and energy balance make up the basic of any chemical engineering plant. Material balance…

Q: Explain path line in relation to fluid mechanics.

A:

Q: If the distance between holes is 50 mm, the distance between the third spot light and the central…

A: Given data: Distance between hole is = d = 50 mm = 0.050 m distance between third spot light and…

Q: ) Explain the working principle of optical pyrometer using clear diagrams.

A:

Q: Create a problem set of 5 problems about material balance. ( Show your solution in each problem)

A: 5 Problems about material balance

Q: Can you explain the stained glass process?

A: The stained glass means colored glass as a material and to works formed from it. The term stained…

Q: How to manufacture ball bearing and what manufacturing processes are involved in manufacturing of…

A: A bearing machine element that enables rotational or linear movement, and reduces friction between…

Q: Present one example depicting the impact of instrumention on one or more process variables.

A: Consider a Water tank with a level controller. Here consider the different process variables. Input…

Q: Create a solver or calculator using MS Excel utilizing different application on Chemical…

A:

Q: What are examples of mechanical operation

A: Mechanical Operations is the operation that is applied on the solids, to get the desired size,…

Q: I want a detailed explanation of the types of crusher and each crusher when to use it, thank you

A: The size reduction equipment is classified based on the type of method they use for the size…

Q: please help meeee

A: 2.10 solution: Anion is the ion with a negative charge. In the given compound, perbromic acid HBrO4,…

Q: Draw Resource Pyramid and discuss its components

A:

Q: If the time of flow of the given mixture is 50 seconds, what is the composition of the mixture? * O…

A:

Q: Explain the friction between the mater (soled with soled, liquid with liquid)?

A: Motion: Motion is the phenomenon in which an object changes its position over time. Motion is…

Q: Differentiate between Unit operations and Unit process in Chemical processing

A: Unit operationsThis term is used in Chemical processing which is defined as the operations in which…

Q: What are the safety equipments needed when conducting experiments in the laboratory? Explain how it…

A:

Q: When we change the fluid package from one package to another, does the temperature and pressure…

A: When we change the fluid package from one another then the following properties will change such…

Steady State Model

The steady-state model typically states that the entire universe is always enlarging, although it balances a fixed average density and matter that is being constantly generated to make new galaxies, star forms at a similar rate that the previous ones get indistinguishable due to the growing range and velocity of recession.