Problem (3) 6.103 P.273: When an air jet of 25mm diameter strike a series of blades on a turbinerotor, the absolute velocities are as shown. If theair is assumed to have a constant weight density of12.6 N/m³, what is the force on the turbine rotor?How much power is transferred to the rotor? Whatmust be the velocity of the blade system?V = 150 m/s,V1V2 = 120 m/s

assume that, there is no friction loss ( relative velocity is constant) and constant pressure…

Answered: 12.6 N/m³, what is the force on the…

12.6 N/m³, what is the force on the turbine rotor? How much power is transferred to the rotor? What must be the velocity of the blade system? V = 150 m/s, V2 = 120 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the power output from the turbine if the turbine efficiency is 75% and velocity at the nozzle 3 m/s and diameter of nozzle 50mm. EL=50m EL=30m D=50mm T D=100mm D=100mm
1. The figure shows a pump that draws 840 L/min of crude oil (s= 0.85) in an underground storage drum to the first stage of a processing system; a) If the total energy loss in the system is 4.2 N m/N of oil flow, determine the power transmitted by the pump to the fluid. b) If the energy loss in the steel suction line is 1.4 N m/N of oil flow, determine the pressure at the pump inlet
In a large pumped hydro plant, the head from the turbine to the lake surface is 100m. During a period of 8 hours of excess electricity in the grid the pumped hydro plant pumps water back into the top reservoir. If the combined efficiency of the pump is 70% and the plant has a capacity of 50 MW how much water is pumped back up to the top reservoir? Assume the head remains constant during pumping. A. 0.5 x 10 – 1.0 x 10 m B. 1.1 x 10 – 1.5 x 10° m C. 1.6 x 105 - 2.0 x 10 m D. 2.1 x 10° - 2.5 x 10 m3
What is the minimum power required from the pump to deliver the oil from Reservoir A to Reservoir B as shown in Figure 2 at a rate of 0.30m³/s? The pump has a 70% efficiency rating. V Reservoir A -Oil v= 10-5 m²/s p=950kg/m³ Elevation 135m Steel Pipe, ks =0.046mm, L= 200m, D=250mm Elevation 120m r/D=0.1 Pump Figure 2 r/d=1 Reservoir B abrupt Globe valve, wide open Air at 200kPa Elevation 110m Elevation 100m
The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.235 m and the pipe lengths are L1= 5 m, L2= 4.5 m, L3= 1.5 m, and L4= 0.6 m. The impeller of the centrifugal pump has a diameter of 0.55 m and operates at 850 rpm. The uniform blade height is 51 mm. The water enters the pump parallel to the pump shaft with a flow rate of 0.16 m3/s. Take viscosity as 0.00112 N s/m2. Fig Q2: Piping system to pump water between two tanks. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3. a) What would be the shaft power required to turn the impeller if the exit blade angle is 31 degrees. b)
In order to meet the stated goal of delivering 4 gallons per minute at a height of 670 meters, a single pump must have a maximum flow rate of 40 gpm. How many stages are needed if the speed cannot exceed 1352 rpm?
A Pelton wheel develops 70 kW under a head of 60 m of water. It rotates 400 rpm. Overall efficiency is 80%. Find the discharge rate in m³/s. Use the equation below, where P is power of the turbine shaft and no is the overall efficiency, where specific weight of water is is 9.80 kN/m³ no P YQH A generator is driven by a small, single-jet Pelton turbine designed to have a power specific speed sp 0.20. The effective head at nozzle inlet is 200 m and the nozzle velocity coefficient is 0.985. The runner rotates at 880 rev/min, The turbine overall efficiency is 80%. Find (a) the power delivered by the shaft of the turbine and (b) find the power delivered by the water to the turbine. where density of water is 1000 kg/m³ and g is 9.80 m/s². Use Stup Ω P/p (gHE)* Overall efficiency ne and Power developed at turbine shaft hydraulic power P YQH
The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . What is the resulting flow rate in the system if three pumps are used in series? (a) 0.56 m^3/s (b) 0.48 m^3/s (c) 0.33 m^3/s (d) 0.36 m^3/s HINT: what is the resulting Flow-rate in the system if three pumps are used in series ? Choose correct option above
A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -8 psi and 44 psi, respectively. The rate of flow in the pipe is 0.714 ft3/s. Neglect energy (friction) losses in the system. Use x = 4 ft., y = 7 ft. Use 1 hp = 550 lb-ft/s. Efficiency of the pump is 91%. What is the input power of the pump, in hp? Round off to two decimal places.
The fluid flow rate was 1 m3 / s and the head was 10 m in the experiment performed at 2000 rev/min by water with the 1/4 ratio model of a centrifugal pump designed to be used for oil. Calculate the power given by the pump to the fluid when the prototype pump operates at 1000 rev/min (ρ water = 1000 kg / m3, ρ oil = 800 kg / m3)
Fans-2 5. The power output is 35 Hp to a centrifugal pump that is discharging 905 gpm and which operates at 1805 rpm against a head H= 125 ft, 220 V, 3 phase, 60 Hertz. If this pump is modified to operate 1205 rpm, assuming its efficiency remains constant, determine its power input to the pump.