Calculate the horizontal (x and y) components of the anchoring force needed to hold the bend in place.

Q: Figure 13 shows a steady flow of 40 kg / s of water at 20 ° C through a nozzle if D1 = 18 cm and D2…

A:

Q: An oil jet (S.G = 0.8) is hitting a fixed vane at flow rate of 0.3 m³/s as shown in the figure. The…

A:

Q: The choked nozzle that converges and diverges. Find the nozzle areas ratio that divides by the…

A:

Q: Q 3: The pipe bend shown in figure (3) is in horizontal plane. Oil with sp.gr=0.86 enters the…

A:

Q: For the sprinkler shown, find a. the torque required to hold it steady, and b. the rotation rate in…

A:

Q: consider the following conditions: a centrifugal pump has diameters d1 = 7 in, d2 = 13 in, blade…

A:

Q: A jet of water of 50 mm diameter strikes a square plate at its centre. The plate weighing 80 N is…

A: F=80N d=50mm

Q: 4. A tank is full of water and open at the top as shown in the figure. There is a frictionless…

A: Solution: Given Data: z1 = 10 m P1=P2=PatmV1=0z2=0

Q: The adjacent picture shows a pipe section in which a reduction sleeve (nozzle) is connected to the…

A:

Q: The flow past a two-dimensional Half-Rankıne Body results from the superposition of a horizontal…

A: Given data,Magnitude- U=2ms

Q: A jet of water strikes a splitter and splits into two streams of equal velocity but unequal…

A: Consider the diagram shown below for the given system. (a) From the conservation of mass, the…

Q: A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded…

A: Given Pressure inside the rocket , Pi = 100 KPa exit area is on tenth of the inside area .

Q: When a gravity-driven liquid jet issues from a slot in a tank, as in Fig., an approximation for the…

A:

Q: Problem 3: Control Volumes When a water jet strikes a stationary inclined plate, it breaks into two…

A: if you have any doubts please comment

Q: The entrance flow between two parallel plates (gap h) has a velocity that varies linearly at the…

A: The mass flow rate () remains constant throughout the flow, given by:where is the cross-sectional…

Q: Find the resultant force in the y-direction Fr,y for a volumetric flow rate in the y direction of…

A: Volumetric flow rateDiameterSo the cross sectional area:Pressure of the flow

Q: For the moving cart and vane in the figure below, let the jet be water of 3 in diameter at 35 ft/s.…

A:

Q: A jet of water of 100 mm diameter is striking a plate with a velocity of 35 m/s. Find the force…

A:

Q: A horizontal pipe ends with a nozzle that discharges to the atmosphere. The pipe has adiameter of…

A: The objective of the question is to find the diameter of the nozzle required to obtain a jet with a…

Q: Consider the pipe shown in the figure below. The nozzle's center line is 0.3 m above the flange…

A:

Q: 2. For the preceding problem, using actuator disc theory, determine the axial flow induction factor,…

A:

Q: A turbine (see the figure of Example IIIa.3.21) is located at an elevation H1 from the surface of a…

A:

Q: 3. A water jet pump has an area A;= 50 cm² and a jet velocity v₁ = 25 m/s, which entrains a…

A:

Q: (3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank…

A:

Q: Fig. 4 , a 2-in-diameter stream of water strikes a 4-ft-square door which is at an angle of 30° with…

A: The Answer is wrong..!!!! Please find the correct procedure and Answer provided below...!

Q: The net pressure force along the horizontal direction (N). Net out flow rate of momentum through the…

A: As per honor code and answering guidelines I can answer 1st, 3 sub parts at time .If you want other…

Q: The cross-sectional area is 25 square centimeter of water jet under the velocity of 35 meter per…

A:

Q: Water flows through a rectangular duct of height h = 575.5 mm and width b = 100 mm. (coming off…

A: Given: U = 58 m/s Vmax = 2Vmin Find: Vmin = ?

Q: As discussed in class, rotor wheel turbines are commonly used in hydroelectric power plants to…

A:

Q: A large commercial power washer delivers 21 gal/min ofwater through a nozzle of exit diameter…

A: Given: Q=21 gal/mind=13 inDensity of water is taken asρ=1.94 slug/ft3 The mass flow rate is…

Q: The airduct shown below has a slanted exit, the dimension of which is 2 inch by 3 inch. Air is…

A: To obtain the solution to the above question, we must apply the ideal gas equation, which is as…

Q: An airfoil shape is shown below. The vectors for the force of the fluid on the airfoil are positive…

A: Airfoil is the basic form of wings. These are curved surfaces. It is used to obtain the helpful…

Q: A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1 =0.120 m is given.…

A:

Q: The open stream of water seen in the following picture emerges from a nozzle into the atmosphere at…

A: Given:Pressure at centerline of section 1, P1=101 kPaDiameter at 1, d1=12 cm=0.12 mDiameter at exit,…

Q: Problem9 The entrance flow between two parallel plates (gap h) has a velocity that varies linearly…

A: In a laminar flow between two parallel plates, the velocity profile is symmetric about the mid-plane…

Q: A jet of water issues from a nozzle with a velocity 41m/s it impinges normally on a flat plate…

A:

Q: estraining force may be given as . The cone angle (8) is

A: