12.4 The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m². What will be the stress along the face AB? (Cambridge) 19.0cm HA -36cm- 1.60 cm 1.90 cm 1.60 cm 17.5cm→

12.4 The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m². What will be the stress along the face AB? (Cambridge) 19.0cm HA -36cm- 1.60 cm 1.90 cm 1.60 cm 17.5cm→

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2) A 150 lb horizontal force, P, is applied to end D of handle ABD in the direction shown. Section AB has a diameter of 1.2 in. a. Determine the stress state at point H (H has sides parallel to the x and y axes). b. Draw a Mohr's circle representation for the point. What are the principal stresses at point H. 10 in. 4 in. y B 18 in. 1.2 in. P x
Use 32 in2 and 48 in2 cross-sectional areas for tensile and compressive members, respectively. Determine the axial stress in member CH in psi. (Numerical absolute answer only without units in 3 decimal places)
Calculate the stress at a-a and b-b sections.a
7) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 40 mm. The diameter of the pressure vessel is 550 mm and its length is 3.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
Hertz contact theory can be used to determine the stresses due to contact between two spheres, which can be used approximate frictionless contact between the patellar and femoral components of a total knee replacement. Part a) Show on a sketch how the stresses at the surface vary from the centre of contact to the edge of contact. Part b) Make a sketch of an infinitesimal element of material at the centre of contact that shows the stress components. Identify the maximum principal stress, and write an expression for the maximum shear stress. Part c) Sketch a graph that shows how the maximum contact pressure varies with load and in a sentence explain why the curve has the shape it does.
Required information Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a diameter of 0.8 in. Take P = 2300 lb. B 2.5 in. 600 lb 1 in. The principal stresses are: ksi A Determine the principal stresses and the maximum shearing stress at point H. (Round the final answers to two decimal places. Input the answers with the appropriate sign.) 3.5 in. max omin = ksi The maximum shearing stress is ksi.
Determine the equivalent state of stress on an element if it is oriented 40° clockwise from the element shown. Ox' = ay' = Tx'y' = 70.2 Mpa -53.8 Mpa 205.6 Mpa + 35.5 Mpa 150 Mpa 32.5 Mpa -70.5 Mpa 64.5 Mpa -100.2 Mpa 100.2 Mpa 50 Mpa 250 Mpa
A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs is applied at the end of a 1.7 in lever arm, causing the pipe to twist. What is the maximum stress in the pipe in psi? 20,766.9 Correct Answer: 124,601
A bolt passing through a piece of wood is shown below. Determine the average shear stress in the wood. Determine the axial stress in the shank of the bolt. Answer options (for the two questions) A. 22.7 MPa B. 28.7 MPa C. 230 MPa D. 20.7 MPa
Q) Two steel rods (E= 206.84 Gpsi) are attached to rigid supports at A and B and connected to each other at C, All connections are smooth pins, The rod have (25.4 x25.4 mm) square cross-section, A 444.822 KN vertical force is applied at C. Determine the axial stress and the elongation of rod AC. 274.3 cm 131.9 em 274.3 cm 1444.8 KN
Question 2 The steel bar has the dimensions shown in Figure 2 below. Determine the maximum axial force P that can be applied if the ultimate normal stress for the steel is 215 MPa and the factor of safety 2.0 is desired. / 3.4 3.2 3.0 2.5 2.4 K 2.2 2.0 1.8 1.6 1.2 1.0 0 0.1 02 (a) Flat bars with holes P. 30 mm 24 mm- 20 mm 60 mm Figure 2 03 04 05 06 07 2r/D 3.2 3.0 2.5 26 K 22 20 1.8 1.6 1.4 12 1.0 r = 15 mm (b) Flat bars with fillets D Did-2 13 13 12 000204000005 0.10 0.12 0.34 0.30 0.15 0.20 0.22 0.24 0.28 0.25 6.30 vid Figure 3: Stress Concentration Factor, K for the Flat Bars
a) Calculate the maximum and average stresses un sections A and B, take t= 0.45in