12.2:The protruding wooden beam shown in the figure; a:)Draw the normal stress and shear stress diagram in the support section and find the maximum values. b:)in wood Ϯsafe=0,9 MPa , ϭsafe= 90 MPa find out if the wooden beam can carry the given load with confidence. Answer: Ϯmax=0,9 MPa , ϭmax= -45 MPa

Q: The figure below are timber planks joined together by a bolt with the corresponding measurements.…

A: Given data: τw=10 ksiσb=20 ksid=34 in Need to determine the maximum safest value of P.

Q: For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at…

A:

Q: A beam system ABC is freely supported in A and C and evenly loaded with q from A to B. In addition,…

A: We have given A beam system ABC is freely supported in A and C and evenly loaded with q from A to B.…

Q: Two blocks of wood, 50 mm wide and 20 mm thick, are glued together as shown in figure below. Using…

A: For solution refer below images.

Q: 10 kN 3 kN/m 100 mm 200 mm B 1.5 m 1.5 m 2.2 m

A:

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A: The applied force is .The dimension are The allowable shear stress is

Q: 2. Given the box beam shown below, and concentrated load P=3500#. a. What is the magnitude of the…

A:

Q: Part A A uniform beam of length L= 7.0 m and mass M = 155 kg is hinged to a vertical wall. The beam…

A:

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: Below is a connection of a Bracing in a Structure that is subject to a Force of 5 KN; please…

A:

Q: P=4 t=14 Tall = 1.6 Strength of Materials HOME WORK1- Stress Member B is subjected to the…

A: P=4 t=14

Q: The figure below shows a simply supported beam with an overbang. The beam is made of two types of…

A: σpi=11 mPa     Epi=8 GPaσpl=14 mPa     Epl=12 GPaFind allowable magnitude w=?

Q: P = 500 N pressing force to the wooden blocks between the jaws. It case; a) Calculate the greatest…

A:

Q: n the system in the figure, a) Since σy=450 MPa and the factor of safety is n=3, Find the…

A:

Q: A bolted connection between a vertical column and a diagonal brace is shown in the figure below. The…

A:

Q: A beam made of Al 2014-T6 aluminum alloy is loaded by an oblique bending moment of M= 5 kN.m as…

A: Solution: a) Centroid of the cross-section y¯ can be calculated by, Let area A1 = 90×10=900mm2…

Q: beam at quarter of the

A: Given ,

Q: Question 2. Consider the beam with a I-beam cross section in Figure 2. Consider point A at the…

A:

Q: Given data : Load =10 N Diameter of circular cross section =2 mm Determine stress

A: Given data,  P= 10 N  Diameter d= 2mm

Q: AWT230 x 26 standard steel shape is used to support the loads shown on the beam in the figure. The…

A:

Q: A beam has the the geometry and dimensions shown in the figure and parameter table. If the allowable…

A: Given:The allowable shear stress, The intensity of the distributed load is

Q: Two blocks of wood, 50 mm wide and 20 mm thick, are glued together as shown in figure below. Using…

A:

Q: A simply supported beam carrying floor joist shown in Figure 6.22 is made of rectangular wood having…

A: Given data: P=1 kN Need to determine the bending stress.

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

A:

Q: Example (5.3): Find the maximum tensile and compressive stresses for the beam shown in Figure (5.6).…

A:

Q: A loading condition of a bracket ABCD having a solid cross section is shown below. Given b1 = 3 ft,…

A: (a) Draw the diagram for AB and transfer the load P at point B, It can be seen that a load P and a…

Q: a) Calculate the reaction forces in terms of F and theta. b) Calculate the internal shear force and…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: The composite beam in the figure is made of timber with an elasticity modulus of 10 GPa and steel…

A: Composite beam of timber ans steel.

Q: a) A lm long cantilever steel (E = 200GN/m²) beam has a cross-section as shown in Figure 2.1. The…

A: For beam L = 1m E = 200 GN/m² Load = 1 kN θ = 45°

Q: Q.2 A square timber beam used as a railroad tie is supported by a uniformly distributed loads and…

A: Given: ununiform distributed load→W1=24 KN and W2=48 KN Hence upward uniform distributed load:…

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

A: We have to determine  a) Calculate the greatest tensile and compressive stresses occurring in the…

Q: What is the maximum length of a uniformly loaded, simply supported beam based on the maximum…

A: The given information in the problem is shown in the following attached image:

Q: The built-up beam is subjected to a moment of M = 80 kNm. d₁ d₁ M₁ de d5

A: To findDetermine the distance from the Neutral axis to the top of the beam, NA.Determine the mass…

Q: Q3: A hexagonal cross section bar as shown in Figure (2) below, is used as a simply supported beam.…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.