12. What is the necessary flowrate to extend a cylinder with an effective cap end volume of 462 in and astroke length of 12 inches at a rate of 2.0 inches per second?Q=13. What is the extension speed of a cylinder with an effective cap end area of 5.0 in? when filled at aflowrate of 1.5 gpm?14. A double acting cylinder has an effective cap-end to rod-end effective area ratio of 3:2. If the extensionspeed at a flowrate of 3.0 gpm is 2.5 inches per second, then what is the retraction speed at the sameflowrate?15. How much work energy is required to lift 1500 Ibs of snow from the parking lot to the top of a snow hill10 ft tall?

Given: V=462 in3L=12 invelocity = 2 in/sec

Answered: 12. What is the necessary flowrate to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the mass flow rate of air entering the carburetor is 0.2 kg/s, assuming the discharge coefficient of the throat is 0.9, find the throat diameter? Select one O a. 0.0237 m O b 0.3 m Oc 0.0346 m O d. 0.32 m Next finge
What maximum working pressure is advisable in an 457.2 mm OD, schedule 40 pipe A53-SA, operations not to exceed 232.2 °C.
Figure 8.18 shows a system used to spray polluted water into the air to increase the water's oxygen content and to cause volatile solvents in the water to vaporize. The pressure at point B just ahead of the nozzle must be 25.0 psig for proper nozzle performance. The pressure at point A (the pump inlet) is -3.50 psig. The volume flow rate is 0.50 ft/s. The dynamic viscosity of the fluid is 4.0 x 105 lbs/ft². The specific gravity of the fluid is 1.026. Compute the power delivered by the pump to the fluid, considering friction energy loss in the discharge line.
Illustrate and discuss the two ways of throttling using one-way flow control valves
11.1 Fluid Mechanics Provide complete solutions and detailed drawings with FBD. *make sure to answer the given table.
1. If a rectangular duct system (12 inch × 26 inch) has an average velocity of 700 fpm, what is the airflow?
c. Discuss why 8 measurements per diameter are used for 400mm diameter round duct, using relevant standard or regulation.
If we assume that a given pump requires 7.50 ft of NPSH when operating at 3500 rpm, what would be the NPSH required at 2850 rpm?
Show in Figure 1 is the water flow system. The velocity head difference is . Volume flow rate is . The heights are and , respectively. The power output from the motor is , . The energy added by the pump is . The energy loss between point 1 and 2 is . Calculate 4) the pressure head difference in meter_________ m
Which among the statement is correct? A Major losses are the head losses that occur due to bends, elbows, joints, valves, and other components. B) Any time the flow experiences a change in direction or a change in cross-sectional area, it will experience a head loss. Head loss is the reduction in the total head (sum of potential head, velocity head, and pressure head) of a fluid caused by the pressure drop during the fluid's motion. (D) A reduction in head loss is experienced when the fluid's velocity is increased, which is often due to pipe friction. E Frictional loss is that part of the total head loss that occurs as the fluid flows through smooth straight pipes.
Inorder to achieve a liquid flow rate of 500 gal/min with a maximum pressure difference of 42 psi, calculate the value of valve flow coefficient. The specific gravity of liquid is 1.3.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

12. What is the necessary flowrate to extend a cylinder with an effective cap end volume of 462 in' and a stroke length of 12 inches at a rate of 2.0 inches per second?