12. The inputs A and B in the figure below can be either 0·V·or +10-V. Each diode is silicon with a forward barrier voltage of 0.7-volts. Find for each of the following cases. ↓ (a) A=0 V, B=0.V↓ (b) A=0 V, B = +10 V↓ (c) A =+10-V, B = 0-V↓ (d) A =+10 V, B =+10-V↓ ↓ AO # BO + + 15 V 1.5 ΚΩ

12. The inputs A and B in the figure below can be either 0·V·or +10-V. Each diode is silicon with a forward barrier voltage of 0.7-volts. Find for each of the following cases. ↓ (a) A=0 V, B=0.V↓ (b) A=0 V, B = +10 V↓ (c) A =+10-V, B = 0-V↓ (d) A =+10 V, B =+10-V↓ ↓ AO # BO + + 15 V 1.5 ΚΩ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q6 Choose correct answer
icdeal diode Es R the source is sinus oidal, the effective value is hov, 7- boHz what is the maximum value of the wollage if the odiode is blocked : the diode is of f the diode ©240V 2. 120V 190 V 340 V
choose the correct answer
For the given circuit below, it operates on a peak-to-peak input voltage of 104.6 V, F = 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. %3D Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1 D2 ... AC Input Vsec B (source) D3 D4 Load O 7.32 3.83 6.63 O 3.74 eele
Analyze the ON/OFF states of all diodes (D1 and D2) inthis circuit, using the ideal-diode model.
4. In the following circuit, the transformer's secondary has a peak voltage of 8V, sketch waveform of Vaut and find its peak voltage. What type of rectifier is this circuit? D1 R1 1000 T1 R2 ·100Ω Vout D2 R3 1000
For the following circuit, draw 2 cycles of the voltage in RL, if the transformer provides a maximum voltage of 40V, the Zener diodes are 15V and 12V, and the rest of the diodes are silicon diodes with forward voltage drop of 0.66V. Indicate the peak value of the voltage in RL.
Design a buck converter such that the output voltage varies between from 20V to 28V while the input voltage is 40V. The maximum load power is 200Wde. Assume the switching frequency is 15kHz. (a) Design the converter such that it will be in continuous current mode. (b) The capacitor realized output voltage ripple must not be more than 1% at worst case. (c) The inductance realizes CCM at worst case. (d) Select the appropriate switch and other elements
Q 5. Find the values of I and V in the circuits shown in Figure. Assume Ideal SI Diode.
IN ALL CALCULATIONS AND THE USE OF THE FOUND VALUES IN THE EQUATIONS, THE PROCESS WILL BE MADE WITH 3 DIGGERS AFTER THE COMMA. Thank you
a) Determine the output voltage for all input voltages values. b) Sketch the overall output waveform, Vo(t).
The diode in the circuits below has a forward voltage drop of 0.6V and a breakdown voltage of 4V. Estimate the current, I_D, through the diode using the CVD model and voltages described above.