Answered: 12- The Pelton wheel shown in Fig. is…

12- The Pelton wheel shown in Fig. is being driven at 200 rpm by a 45 m/s jet of water. The jet diameter is 6 cm. Determine the power developed by the wheel? [Ans. Power-124.65 kW] 1.2 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m. The runner blade angles are ?2 = 71.4° and ?1 = 15.3° at the turbine inlet and outlet, respectively. The runner rotates at n. = 160 rpm. The volume flow rate at design conditions is 80.0 m3/s. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (MW) and required net head (m).
The cylinder bore diameter of a double-acting reciprocating pump is 170 mm and its stroke is 370 mm. The pump runs at 55 rpm and lifts water through a height of 26 m. The delivery pipe is 23.5 m long and 113 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 13 liters/s. Assume the weight density of water is 9810 N/m3 (i)Theoretical discharge in liter/s (ii) the theoretical power required to run the pump in kW (iii) the percentage of slip (iv) the coefficient of discharge.
Che
I need the answer as soon as possible
The original design of a hydraulic turbine has data as follows: flow rate of 1 cumex, effective head of 50 m, and runner diameter of 1.5 m. If the same turbine design is to be used in another application where the available flow is 2.5 cumex and effective head is 75 m, what would be the runner diameter (in meters) for this new application?
A pump has overall efficiency of 70 %. It delivers 90 Ipm at 1000 rpm and 700 N/cm". If the prime mover input torque is 12 KN-cm, calculate a) the actual torque of the pump b) volumetric displacement in cm. Comment on the significance of torque in pumps. 3
A hydraulic vane pump running at 1800 rpm develops 2 L/s flow at 750 kPa. Volumetric efficiency is .85 and overall efficiency is 0.8. Determine the Theoretical Torque required, TT (N-m). (Hint: first calculate the mechanical efficiency and theoretical flow rate. Convert rpm to rad/s). O 9.41 N-m 8.85 N-m 9.35 N-m 9.62 N-m 8.80 N-m
Using data given below, determine the main dimensions and blade angles of a Francis turbine. Net head=65 m, speed= 700 rpm, BHP= 400. Actual hydraulic efficiency3D 94%, overall efficiency= 85%, flow ratio= 0.18, wheel width at inlet/ wheel diameter at inlet=0.1, inner diameter/ outer diameter= 0.5. Assuming constant velocity of flow and radial discharge. Neglect area blocked by blades. Vane angle at inlet: 27° 39 33° 53 41° 82 O 52° 56
A pump has overall efficiency of 70 %. It delivers 90 Ipm at 1000 rpm and 700 N/cm". If the prime mover input torque is 12 KN-cm, calculate a) the actual torque of the pump b) volumetric displacement in cm". Comment on the significance of torque in pumps. A BI
Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. How many hp is needed for the pump to function if its efficiency is just 80%?
1.) A horizontal pipe bent reduces from 300 mm bore diameter at inlet to 150 mm diameter at outlet. The bend is swept through 50° from its initial direction. The flow rate is 0.05 m3/s and the density is 1000 kg/m³. Calculate the momentum force on the bend and resolve it into two perpendicular directions relative to the initial direction. 2.) A jet of water traveling with a velocity of 25 m/s and flow rate of 0.4 kg/s is deflected 150° from its initial direction by a stationary vane. Calculate the force on the vane acting parallel to and perpendicular to the initial direction.
Hydro electric station is installed to utilise 30 ma/sec of water of a river at a head of 7.5 m. If 85% turbine efficiency can be counted on, (i) is it feasible to develop this power by two turbines with rpm not less than 50, the turbine having specific speed not greater than 540 rpm ? (ii) what type of runner will be used ? (iii) what is the diameter of runner if the speed ratio is 0.85? [(i) N = 156'5 rpm, .. yes (ii) Kaplan (iii) P25 m]