200 kN/mTurbine0.3 m/s'0.4 m dia.- 20 kN/m0.6 m dia.Fig. 6.96In Fig 6.96 what is the powerdeveloped by theturbine assuming efficiency of80%?[Ans. 54 kW]jo 12:24

givenat inlet of turbine pressure P1=200KPadischarge Q=0.3m3/sdiameter of pipe d1=0.4mhieght of…

Answered: 200 kN/m Turbine 3 0.3 m /s'0.4 m

Engineering

Mechanical Engineering

200 kN/m Turbine 3 0.3 m /s'0.4 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 4a) A Ship must discharge a total of Seawater ballast 2200 cubic meters of Within 6 hours. Using S…

A: given; (a)discharge volume=2200m3at time (t)=6 hours =6*3600 secdiameter of…

Q: Q3: calculate the total residual flow using the following data Static pressure: 55 psi Residual…

A: Write the measured residual pressure. Pr=41 psi Write the desired residual pressure. Pd=20 psi Write…

Q: Find the friction for water at 60°C flowing at 0.0057 m³/s in a 4 in Sch 40 steel pipe.Answer to 3…

A: <math style="font-family:'Times New Roman'"

Q: Find the specific speed of the pump, if the discharge through the pump is 160 liters/sec, speed is…

A: Given values are, discharge Q= 160litres/sec=160×10-3m3s speed N=1000rpm ,head H=27.5 m The specific…

Q: 1st: Using the formula t=24(/h3/h2) determine the "A" of tank Caa/2g coefficient of discharge. Note:…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: ump efficiency= 97% Pump speed= 1848 rpm Pump discharge= 172L/s of water to a height at 61 m.…

Q: In the below system, the pump uses 20°C water. If z2 = 225 ft, what is the flow rate (in ft3/s) if d…

Q: where do v sub 1 came from? which is 0.95m/s

Q: The pump in figure 3 delivers water from the reservoir to the nozzle at the rate of 0.13 m/s. The…

Q: 3. Based from the pump performance curve below, calculate the following: a) Specific speed b)…

A: Given data Pump performance curve From the pump performance curve, specific speed and suction…

Q: 1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm…

A: Given data Flow rate = 500 gpm Pressure = 35 psi Density = 62 lbm/ft^3 Find the pump head

Q: In the system, 900 L/min of oil is pumped with (s=0.92), from an underground storage tank to the…

A: Given: The flow rate of the oil, Q = 900 L/min The specific gravity of the oil, SG = 0.92 The loss…

Q: Q2/ If the turbine extracts 400 kW from the flow, what flowrate must be passing through the system?…

Q: Calculate the NPSHA in ft for the following configuration of pumping system. (Hint: Use steam tables…

A: Net Positive Suction Head is the pressure margin over vapour pressure at the pump suction nozzle…

Q: 8.78. A pump is designed to operate at 1 800 r/min with 83.7% efficiency, and deliver 250 1/s with a…

A: Given:N=1800 rpmη=83.7%Q=250 L/s =250*10-3 m3/sP=141 KW

Q: Q1/ A45' reducing bend is connected in apipe line, the diameters at the inlet and outlet of the bend…

A: Answer: The force exerted by water on the bend is 20891 N at 17.62° in clockwise direction from…

Q: Select the number and type (ns ) of centrifugal pumps for a pumping station that must deliver 130…

A: identical single-stage pumps in parallel.Qt=130 m3/sH=50mN=180 rpmNPSH=+5

Q: Flow Pump 6-in Schedule 40 4-in Schedule 40 4 in Engine Oil 30 in Mercury (sg =13.54)

A: Calculate the pressure change from point 1 to point 2. P1-ρoilg4 in-ρhgg30 in+ρoilg34…

Q: 4- A Pelton wheel has a mean bucket speed of 10m/sec with a jet water flowing at the rate of…

A: Given:u=10 m/sQ=700 L/s =0.7 m3/sH=30 mθ=160°cv=0.98

Q: Hydraulic pump calculations Pressure = 600 PSI Displacement (D) = 0.4in3/rev 1150 RPM Total…

A: The given data in the question is: Pressure = 600 PSI Displacement (D) = 0.4 in3/rev Speed = 1150…

Q: Question 2. la0 mm diameter siphon draws water from the reservoir. Considering that the elevation…

A: Given diameter =4mm=0.004 m h(1)=1m h(2)=1 m

Q: Prob-2 HL=8.5 m Compute discharge pressure of Pump: Elevation=50m Psuction =-40Kpag D Pdischarge = ?…

Q: Q2- A (0.14 m'/s) oil has (density 860 kg/m' & viscosity 0.026 pa.s) is pumping from first tank to…

Q: Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside…

Q: Determine the recommended minimum speed (rpm) for a radial flow pump operating at 0.165 m3/s of…

Q: Inlet and throat diameters of a horizontal venturimeter are 250 mm and 100 mm respectively. The…

A: Inlet diameter, d1=250 mm=0.250 m Throat diameter, d2=100 mm =0.100 m Pressure at inlet, P1=15…

Q: Plate 30m V, Rx= Given z Rx = 890 Y %3D water

A: Given that, Rx=890 N,head of water, h=30 m,θ=90°ηt=90 % v=2ghv=2×9.81×30v=24.261 m/sec The…

Q: n the Picture above OBE locm /Bc = 2Scm Ehe Vtelve of nŋ or rotation cl dao rem Convert this vawe to…

Q: 0 oil volume flow rate

A: given:

Q: installed as shown in the figure. The gage at point 1 is 80 kPa while at point 2 is -46 kPa. If the…

Q: 3. Based from the pump performance curve below, calculate the following: a) Specific speed b)…

A: Given data pump performance curve Specific speed and Suction Specific speed is to be calculated.

Q: 1. A pump delivers gasoline (SG = 0.74) at 20°C and 12 m/h. At the inlet pa= 100 kPa, z =1 m, and V…

Q: Show in Figure 1 is the water flow system. The velocity head difference is = 2.0m. Volume flow rate…

A: Given data as per the question velocity head =2 m volume flow rate =0.5 m3/s h1 =1 m h2 =2 m hA = 3…

Q: A pump with a volumetric displacement of 4 in^3/rev runs at 3600 rpm and produces 1500 psi. The…

A: The volumetric efficiency of the pump.Given:The volumetric displacement is .The angular speed of the…

Q: 3. A centrifugal pump having an impeller of diameter 500 mm delivers 140 litres of water per second.…

Q: Convert a flow of water flowing in a pipe 340 Liters/ hr into _m³/min kg/hr, discharge in kg/hr…

Q: In the figure shown, it is desired to pump 40 L/s of water from a natural stream to a small…

A: INTRODUCTION: When water flows through the pipe, the head loss is inevitable. Minor and significant…

Q: Hydraulics 7. A turbine has a velocity of 6 m/s at the entrance to the draft tube and a velocity of…

A: Let ρ =Density of water =1000kg/m3 v1 =Velocity of water at entrance =6m/s v2 =Velocity of water at…

Q: You are working as a trainee engineering in a company ABC, is the leading manufacturing company for…

Question

200 kN/m
Turbine
0.3 m/s'0.4 m dia.
- 20 kN/m
0.6 m dia.
Fig. 6.96
In Fig 6.96 what is the power
developed by the
turbine assuming efficiency of
80%?
[Ans. 54 kW]
jo 12:24

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

26
Hydraulic Machines Please write clearly
Please explain step by step
-Q4:- If the wind speed measured on 10 m height from the earth. What the height of wind h? turbine tower should be if the turbine work on 5m/s. Discuss the height from the earth surface with roughness, if the surface are 1. Sandy surface is vary between (0.1-0.13). 2. Trees surface is vary between (0.2-0.25). 3. Hily surface is vary between (0.5-0.9).*
Discuss the fixed displacement vane pump with a neat diagram and derive an expression for theoretical discharge.
Solve fast with Proper Equation. 1. A centrifugal pump delivers 2.5 cfs of water against a head of 25 ft at 1500 rpm and requires 10 hp. If the speed is reduced to 1250 rpm calculate the power , assuming the same efficiency. Select one: a. 17.3 kW b. 13.7 kW c. 5.8 kW d. 8.5 kW
A three stage pump delivers 2.66 m3/s against a head of 200 m with a speed of 2000 rpm. Find the specific speed (US)
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. -4.67m B. 12.74m C. -2.72m D. 2.56
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74m B. -4.67 m C. -2.72 m D. 2.56
A Centrifugal pump operates at a speed of 1450 rpm and discharge of 250 m³/hr against a head of 40m and efficiency=55%. 1- Calculate the pump power 2- Compute the discharge, head, and pump power if the pump speed were changed to 2900 r/min?
Use the Goulds Pump Selection System to find a pump capable of delivering at least 500 gpm against an elevation gain of 120 ft. Use 150 ft as the pump head to be safe.
If a pump with a manometric head of 12 m is designed to deliver a flow rate of 7500 liters / minute. Since the rotation speed of the pump shaft is 1800 rpm, what is the dimensionless pump specific speed of this pump?