12 kips 5 in.

Q: A couple of magnitude M is applied to a square bar of side a. For each of the orientations shown,…

A: Given that: The edge of square cross section is: a.   The bending moment equation is given as:…

Q: Ex : Two solid cylindrical rods AB and BC are welded together at B and loaded as shown , Knowing…

A:

Q: Air pressure in the cylinder is increased by exerting forces P = 2 kN on the two pistons, each…

A: Given Data: The outer radius of the cylinder is: rO=47 mm The force exerted on the walls is: P=2…

Q: The couple M is applied to a beam of the cross section shown in a plane forming an angle b with the…

A: Given:The couple is the angle is

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the internal…

A:

Q: 4.17. Determine the components of stress from the results obtained in (a) v=rsin 0, ve = 2r cos 0…

A: Sure, based on the image you sent, which is a circuit containing a battery, resistors, and an…

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: The couple M acts in a vertical plane and is applied to a beam oriented as shown. Determine (a) the…

A: Given The value of applied couple, M is = 120 N·m. The value of moment of area about y’ axis, IY’ is…

Q: The split ring shown has an inner radius ₁0.6 in. and a circular cross section of diameter d= 0.8…

A:

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

A:

Q: 5 in. 2. Two wooden members of uniform rectangular cross section are joined by a glued scarf splice…

A:

Q: For the shown static system, determine the minimum diameter of cable BD to withstand the shown load,…

A:

Q: Why is the net area for AB (0.045-0.0102) * (0.012) ? Why is AB in tension and BC in compression

A:

Q: A basketball has a 300-mm outer diameter and a 3-mm wall thickness. Determine the normal stress in…

A: Outer diameter, D = 300 mm  Wall thickness, t = 3 mm  Inner diameter, d = D - 2t = 300 - (2*3)  d =…

Q: 20 kN 0.25 m B 0.4 m Each of the four vertical links has an 8 x 36-mm uniform rectangular cross…

A:

Q: The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by…

A: Given Data: The load on member is P = 1.4 kip. The cross-section area is A = 3 in ×5 in. The angle…

Q: THE FRAME SHOWN CONSISTS OF FOUR WOODEN MEMBERS, ABC, DEF,BE, AND CF. KNOWING THAT EACH MEMBER HAS A…

A:

Q: 1.25 ft Determine the maximum allowable weight of passengers on the gondola ride which is suspended…

A: Given, σallowable=18 ksisquare solid steel = 1.5"

Q: Problem 8-12 A bar of rectangular cross-section, with a width of 60 mm and a thickness of 40 mm, is…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.