12 k 2 mA 4 mA P19

Q: Vin + D₁ . + C₁1 RL Vout The rectifier above drives a 950- load with a peak voltage of 3.15V. For a…

A: Solution: Given Data: →Peak Voltage=3.15V→Smoothing…

Q: GLS)=- 100 (S+1)(s+10) (S+50 PM=? GM =? Static Error constant = %3D

A: According to question: a) The phase margin of the given system is calculated as…

Q: Vin D₁ C₁ RL + Vout The rectifier above drives a 640- load with a peak voltage of 3.75V. For a…

A:

Q: QUESTION 10 What is the PIV thru each diode? Use approximate diode model. 110Vrms 5:1 O 31.11V O…

A: In this question we need to find the PIV of the given bridge rectifier.

Q: The basic reason why a Full-wave rectifier has half the ripple factor of a Half-wave rectifier is…

A:

Q: imo a b 202 32

A:

Q: Sir For uncontrolled half wave rectifier, R=80ohm, L=0.15H, f=50HZ and Vm=311V. Calculate the rms…

A:

Q: Quèstion 9 The output voltage V. of the following circuit during the positive half cycle considering…

A: In this question , we will find output voltage during positive half cycle..

Q: 2. Transistor in Saturation 1. Connect the circuit as shown in Figure 1. 2. Connect the base…

A: Given circuit is shown in below figure. When base is connected to ground

Q: Vin + D₁ . 19 - + RL Vout The rectifier above drives a 950- load with a peak voltage of 3.15V. For a…

A:

Q: A pressure sensor gives 0.1 at O psia and 4.75 at 60 psia. we want to transmit this information…

A: Given data: Pressure sensor gives : 0.1V at 0 psia4.75 V at 60 psia Current standard : 30 mA to 110…

Q: D1 D2 20 VP-P VOUT 9V 4.5V

A:

Q: what does the capacitor of Two conductors separated by an insulator Two conductors only Twe in…

A: For Series circuit equivalent capacitance is (two capacitors in parallel): Series connection: When…

Q: If the ripple factor of a rectifier is 30% for an average voltage of 2V, its ripple rms voltage…

A: If the ripple factor of a rectifier is 30% for an average voltage of 2V, its ripple rms voltage…

Q: The electron beam of CRO usually passes through O One pair of deflection plates O Fluorescent screen…

A: The explanation is as follows.

Q: he output voltage Va of the following circuit during the positive half cycle considering ideal diode…

A: During the positive half cycle as the 20volt potential is applied then Capacitor gets charges…

Q: Please answer in typing format

A:

Q: time of a softners factor 2.3 recovesy oliode is t. Sus and the reverse $F=0.5 Pot both QAR and The…

A:

Q: 1. Compute voltage peak. Is it equal to what you are expecting base from the set values of your VAC…

A: The diodes are made of semiconductor materials. Silicon and germanium are common semiconductors for…

Q: data sheet of the following

A: The names of different electrical and electronics elements are given. We need to show the datasheet…

Q: What is the peak output voltage for this half-wave rectifier? + Pri 169.706 V 60 Hz 0 Deg 20:1…

A:

Q: 1. Find the minimum output expression for circuit of figure below and draw logic circuit. A

A: In this question we need to minimize the output expression and logic gate.

Q: Analyze this circuit A J Q Y K D Q Clock 20

A:

Q: al How wave Graercise b) How many rectifier many rectifier c) Explain wildth 2 have dia des have…

A: 1)the three-phase diode rectifier converts a three-phase AC voltage at input into the DC voltage at…

Q: Lhpice X - Draft Herarchy Yew Smulate Jools Window Belp E3 An ap E D (D Vind01) Vind02)-Vin003) KD1)…

A: When positive half cycle of the input is applied, Note: Diode is ON when the positive input voltage…

Q: Si + 20 V Si • 10 ΚΩ +8V Si • Vo

A:

Q: A single phase full wave rectifier supplies a 20 Ohm load at an average voltage of 15 V. Determine…

A: Given: Single phase full wave rectifier Load, RL=20 Ω Average supplied voltage, Vavg=15 V

Q: C. The barrier potential for the diode in Figure 10 is 0.7 V. Determine the output voltage and the…

A:

Q: * The PIV for the (Idle diode) is the circuit is V₁=120 Vac 60 Hz 3:1 V₂ RL=100 Vout 18.5V O 56.56V…

A: for half wave rectifier , PIV voltage = Vm .  where Vm is peak value of secondary voltage of…

Q: A germanium diode draws 32 mA with the forward bias 0.27 V. If T=300 K, calculate the reverse…

A:

Wheatstone Bridge Method

A Wheatstone bridge is a circuit used to measure unknown resistance by measuring the ratios of the two branches of the circuit such that each branch has two resistance and out of four resistance one is unknown. The two branches are joined in between with the help of galvanometer which is used to determine the direction of the current. The main advantage of this circuit is that it can provide the most accurate measurement (different from a simple voltage separator).