12 in. E 12 in. A steel loop ABCD of length 5 ft and of -in. diameter is placed as shown around a l-in.-diameter aluminum rod AC. Cables BE and DF, each of -in. diameter, are used to apply the load Q. Knowing that the ultimate strength of the steel used for the loop and the cables is 70 ksi, and that the ultimate strength of the aluminum used for the rod is 38 ksi, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. 9 in. 1 in. 9 in. in. 응 in. F

12 in. E 12 in. A steel loop ABCD of length 5 ft and of -in. diameter is placed as shown around a l-in.-diameter aluminum rod AC. Cables BE and DF, each of -in. diameter, are used to apply the load Q. Knowing that the ultimate strength of the steel used for the loop and the cables is 70 ksi, and that the ultimate strength of the aluminum used for the rod is 38 ksi, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. 9 in. 1 in. 9 in. in. 응 in. F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 3. A steel wire with a square cross-sectional area (one of its side is 3mm) is used to support a…

Q: A 5.3-m-long steel rod must not stretch more than 2.71 mm and the normal stress must not exceed 181…

A: GivenL=5.3m∆lim=2.71mmσallow=181MPaE=193.3 GPa=193.3×103 N/mm2P=9.99 KN

Q: A metal bar AB of a weight W is suspendedby a system of steel wires arranged as shown in thefigure.…

A: Given: Let,L=Length of side perpendicular to bar=5ina=Length of side parallel to bar=2inHypotnuse…

Q: (a) A steel cylinder of 60 mm inner radius and 80 mm outer radius is subjected to an internal…

A: Note: As per the bartleby guidelines only three subpart will be solved at a time for remaining…

Q: 2. A single horizontal force P of 200 lb is applied to end D of lever ABD. Determine the internal…

A: Given DataHorizontal force at end D of the lever, P=200 lbThe diameter of portion AB of the lever,…

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

Q: 8.13 Determine the load carrying capacity of a hook of rectangular cross-section. The thickness of…

A: Givent=75mmRi=150mmRo=250mml=75mmσall=70MN/m2=70 N/mm2 '

Q: 4- A Pelton wheel has a mean bucket speed of 10m/sec with a jet water flowing at the rate of…

A: Given:u=10 m/sQ=700 L/s =0.7 m3/sH=30 mθ=160°cv=0.98

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

A: Given data A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is…

Q: 1-What is the average normal stress at section b-b? 546.1 kPa 267.7 kPa 813.8 kPa 779.9 kPa 942.8…

A: Given, W=200 N/m θ=550 The cross-section (square) of AB, a=1.5 cm=0.015 m The diameter of the pin at…

Q: The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in…

A: Given:Cable diameter = 4mmE =200 GPaMax Stress 190

Q: Two cylindrical cross-section rods AB and BC, which are fixed to the wall and welded together at…

Q: A load P is supported as shown by a steel pin that has been inserted in a short wooden member…

A: σut=145Mpa in shear

Q: A rigid bar AD is attached to two springs of constant k and is in equi-librium in the position…

A: Draw the free-body diagram of the rigid bar after rotation. Consider the rigid bar rotate through…

Q: 1. Knowing that the ultimate load for cable BD (diameter is 20 mm) is 110 kN and that a factor of…

Q: The 1800-lb load P may be moved along the beam BD to any position between stops at E and F. Knowing…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load…

Q: determine the largest load P t

Q: The 2300-lb load P may be moved along the beam BD to any position between stops at E and F. Knowing…

Q: When a 5 m long, 5 mm steel wire was subjected to a tensile load its stretches by 5 mm. Determine…

A: Load is a force or weight applied on an object. In mechanics, load is a force that acts on a body…

Q: As shown on the right, two circular rods (CE and DF) are attached to a rigid bar (ABCD). Knowing…

Q: A 6.87-m-long steel rod must not stretch more than 2.5 mm and the normal stress must not exceed 181…

Q: A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E = 30 ×…

Q: Problem 2. A steel tube of outer radius 5.8 cm is used to axially support a 100 kN load. If the…

Q: A square aluminum bar is to support a load of 40 kN on a length of 3 m. Assuming pinned ends,…

A: Given that: Cross section of the bar is a square. Let a = length of each side in mm. l = length of…

Q: A { in 2 in 40 KIPS in 1.5 in C 30 KIPS in 2 in D 34

Q: 3 in. 2 in. В C P Q 30 in. 40 in.

Q: Two wooden members of uniform rectangular 150 mm cross-section are joined by a simple glued scarf…

A: Given: Maximum permissible shear stress τmax=620kPa

Q: Question (1): A square yellow-brass bar must not stretch more than 2.5 mm when it is subjected to a…

A: According to the given data σAllow=180MPaP=40kN∆L=2.5mmE=105GPa We need to find (a) Maximum length…

Q: A 1-in.-square aluminum strut is maintained in the position shown by a pin support at A and by sets…

A: E = 10.4E+6 psi I = bh3/12 = 0.083333 in4 Lef = 2 Ldc Ldc = Lef/2 in.............(1)

Q: A W8 x 21 rolled-steel shape is used with the support and cable arrangement shown. Cables BC and BD…

A: Given: The rolled steel shape is W8×21. The length is L=24 ft12 in1 ft=288 in. The Factor of safety…

Q: A 12-kN tensile load will be applied to a 50-m length of steel wire with E= 200 GPa. Determine the…

Q: A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load…

A: length, L=10-in Sides of the block a=1.8 in, b=1.6 in normal stress = 18 ksi…

Q: The steel frame shown has a diagonal brace BD with an area of 1548 sq.mm. Determine the largest…

Q: ABCD as shown. Knowing that the rods are made of aluminum and using E = 73 determine (a) the force…

A: E=73GPa To find force in each rod and deflection at point A

Q: An aluminum structural tube is reinforced by bolting two plates to it as shown for use as a column…

Q: Link BD consists of a single bar 1 in. wide and 12 in. thick. Knowing that each pin has a 38-in.…

A: The provided system is shown below.To determine:

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

12 in.
E
12 in.
A steel loop ABCD of length 5 ft and of -in. diameter is placed as
shown around a l-in.-diameter aluminum rod AC. Cables BE and DF,
each of -in. diameter, are used to apply the load Q. Knowing that the
ultimate strength of the steel used for the loop and the cables is 70 ksi,
and that the ultimate strength of the aluminum used for the rod is 38 ksi,
determine the largest load Q that can be applied if an overall factor of
safety of 3 is desired.
9 in.
1 in.
9 in.
in.
응 in.
F

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A load P is supported as shown by a steel pin that has been inserted in a short wooden member hanging from the ceiling. The ultimate strength of the wood used is 60 MPa in tension and 7.5 MPa in shear,while the ultimate strength of the steel is 145 MPa in shear. Knowing that b = 40 mm, c = 55 mm, and d = 12 mm, determine the load P if an overall factor of safety of 3.2 is desired.
please solve it clearly on a white sheet of paper
16 The length of the 32-in.-diameter steel wire CD has been adjusted so that with no load applied, a gap of in. exists between the end B of the rigid beam ACB and a contact point E. Knowing that E = 29 × 106 psi, determine where a 50-lb block should be placed on the beam to cause contact between B and E.
Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing that the maximum allowable tensile stress in the glued splice is 63 psi, determine the largest load P that can be safely supported if W = 2.1 in, L = 10.5 in and e= 66.2. Round off the final answer to two decimal places. 012.png ... W P'
The 2000-lb load may be moved along the beam BD to any position between stops at E and F. Knowing that σall = 6 ksi for the steel used in rods AB and CD, determine where the stops should be placed if the permitted motion of the load is to be as large as possible.
Two wooden planks, each 1212 in. thick and 9 in. wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 1.8 ksi, determine the magnitude P of the axial load that will cause the joint to fail. The magnitude P of the axial load that will cause the joint to fail is kips.
The steel frame shown has a diagonal brace BD with an area of 1612 sq.mm. Determine the largest allowable load P (in N) if the change in length of member BD is not to exceed 1.27 mm. Use x = 4.4m, y = 5.76m, and E = 197 Gpa. Express your answer in four decimal places. ... B D X.
PROBLEM 1 Determine the allowable weight that the assembly can handle if the cable AB has a working stress of 200 Mpa and cable AC has a working stress of 150 Mpa. The cable cross sectional areas are 300 mm? for cable AB and 330 mm2 for cable AC. B 50° 28° A W
Determine the largest axial load P that can be safely supported by a flat steel bar consisting of two portions, both 10 mm thick and, respectively, 40 and 80 mm wide, connected by fillets of radius r=4 mm. Assume an allowable normal stress of 180 MPa.
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a xin. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.75 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 16 IN 8 in 16. ---4 in- The largest load P that can be applied at Dis[ lb.
A 65 mg mass travels in a horizontal circular path at a speed of 2.2 m/s around the surface of the stationary drum. All surfaces are assumed to be frictionless. Determine the radius of the path, the normal force between the particle and the drum. ANS. a₁=ay=0 N=0.788 N an = 7.127 m/s² 36° r = 0.679 m.
only HANDWRITTEN answer needed ( NOT TYPED)