-12 in- y 0.5 in. |-2,5 in- 2.5 in.-| +2.5 in. 0.5 in. -0.5 in. h 0.5 in.- 8 in. 0.5 in. -6 in-

Q: 55. The pachometer is used to locate the

A:

Q: Determine the centroid of the given composite figure. The area of the geometric figures drawn in red…

A:

Q: Determine the total area if the composite figure. (in^2) Determine the x coordinate of the centroid…

A:

Q: Centroids and Moment of Inertia for composite figures Determine the centroids (x, ỹ) of the figure…

A:

Q: A composite beam is simply supported over a span l and carries a single point transverse load, P as…

A: Given data: The dimensions of Section 1 are: b1=100 mm, h1=8 mm, l=0.4 mm. The dimensions of Section…

Q: Find the centroid point of the area below given that a = 12 in. a a Solution: • The composite area…

A: Given data:- The given value of a is 12 in. After cutting the section,

Q: A hollow circular shaft has an external diameter of 120 mm and internal diameter 60 mm. if the…

A:

Q: P2 Ans: 5000 For the cross sections shown in figure (a) and (b) compare the 0.005m 0.2m torsional…

A: Given data,  Inner radius = 0.2 m Thickness = 0.005 m   To find out the radio of Torsional rigidity.…

Q: Q. No. 4: An aluminium Z section has the dimensions shown in Figure Q. No.4. The yield strength…

A:

Q: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading…

A:

Q: F EI EI a- + F=kx=k(1) k=? *k is Flexural stiffness

A: The solution is: As we have assumed that the hinge support is the fixed support.

Q: 2. A rigid bar with negligible mass is pinned at O and attached to two vertical rods as shown.…

A:

Q: A reinforced concrete beam has a width of 300 mm and an effective depth of 450 mm. The beam is…

A: Given: Required : Balanced steel ratio Depth of compression stress block Nominal moment capacity

Q: Problem #2: y-axis Note: F numbe Use 10 in. A (in.) > х-ахis в (in.) 6 in. 5 in. 4. Determine the…

A: As per bartleby policy we can't give answer more than 3 sub-parts for multiple sub-parts. Please…

Q: *10-40. Locate the centroid y of the composite area, then determine the moment of inertia of this…

A:

Q: Determine the stress at member FE if Pu = 18.375 Kips, the area is 11 in?. Answer your problem with…

A: Given data in question  Loads Dimensions of truss Span member length  Area To find out  Stress in…

Q: Determine the total area if the composite figure. (in^2) Determine the x coordinate of the centroid…

A: A composite section have been given in the question and it has been asked to determine x and y co…

Q: Assume that the truss is simply supported at joints M and E. Determine the stress at member HI if Pu…

A:

Q: 2. In the figure shown, a. What is the distance of the centroid of the composite section from the…

A:

Q: Two forces are applied to the construction bracket a shown. Determine the angle which makes the…

A: GivenR=RyRx=0

Q: A laterally supported, compact beam is simply supportéd át Böth ends. It is subjected to loads that…

A: Option (c)is correct. 1291 KNm is the answer. By the relation , Design capacity of beam = Resistance…

Q: Assume that the truss is simply supported at joints M and E. Determine the stress at member FC if Pu…

A: Given Data : at member FC  Pu = 18.375 Kips  area = 23 in2

Q: A sheet of copper is stretched bi-axially in the xy-plane. If the strains in the sheets are Ex=0.40…

A:

Q: F=kx=k(1) k=? *k is Flexural stiffness

A: Given, F = KxF = K

Q: A steel bar AD has a cross-secțional area of 260 mm? and is loaded by forçes P, = 12 kN. P,= 8 kN.…

A:

Q: Rigid member BED is supported using steel rods AB, CD, and EF as shown below. E-200 GPa for steel.…

A: Using member BED as free body. Due to symmetry, PAB = PCD  .............(1)∑Fy = 0PAB + PCD + PEF =…

Q: (b). A composite bar of steel and brass is subjected to a tensile load P with a uniform FEB length…

A:

Q: 3) Considering a three - beam loaded by a P concentrated load P at the mid – span, prove that the…

A:

Q: Problem 5.6 Determine the force in each member of the truss. Set P = 3.1kN and P2 = 2.3kN. 30 30 C E…

A:

Q: H= 3 R= 1 Inputs: • Center of Circle is the SAME as the Rectangle. • H= Height in cm (From Table) ●…

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.