do fast 12-87.The catapult is used to launch a ball such that it strikes thewall of the building at the maximum height of its trajectory.If it takes 1.5 s to travel from A to B, determine the velocityVA at which it was launched, the angle of release 0, and theheight h.

Answered: Image /qna-images/answer/95556524-b148-42e3-ac0a-3bac1d5fcbae.jpg

Answered: 12-87. The catapult is used to launch a…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter10: Introduction To Simulation Modeling

Section: Chapter Questions

Problem 41P: At the beginning of each week, a machine is in one of four conditions: 1 = excellent; 2 = good; 3 =...

See similar textbooks

Similar questions

1m radius disk is moving on the inclined surface under no slip condition. the center of the disk has 3m/s velocity and according to the figure, bar BC is pinned to the disk at point C and point B always stays on the ground. 1) find angular velocity of BC. 2) find angular acceleration of BC
Water entering the curved pipe at A is discharged at D. The pipe is rotating about A at the constant angular velocity omega=7 rad/s, and the water has a constant speed of v=19 m/s relative to the pipe. Now fill in the blanks below with correct numbers. Αγω သ B 0.54 m r = 0.18 m The magnitude of acceleration of the water just before it is discharged at D= m/s^2 0.30 m
2. An artillery piece and integral supporting base weigh 1800 lb and have a recoil spring for which k = 24000 lb/ft. When fired, the system recoils 40 in. A dashpot having a critical damping constant is the engaged on the return stroke. Determine: (a) The initial velocity of recoil (b) The damping constant (c) The position of the gun and base at 0.5 sec of the return stroke.
13 4. A ramp is attached to a mover's truck. The ramp is 7 ft long and the truck is 6 ft from the bottom of the ramp. A diagram of the ramp with dimensions is below. 7 ft x 6 ft To the nearest degree, determine the angle that the ramp makes with the ground. Hint: 0 = = adjacent hypotenuse = trig ratio used Remember you will need to use your inverse function on your calculator to find the angle.
I need answer typing clear urjent no chatgpt used i will give upvotes
I need typing clear urjent no chatgpt use i will give 5 upvotes
Bill Hardgrave, production foreman for the Virginia Fruit Company, estimates that the average sales of oranges is 4,700 and the standard deviation is 500 oranges. Sales follow a normal distribution.a) What is the probability that sales will be greater than 5,500 oranges?b) What is the probability that sales will be greater than 4,500 oranges?c) What is the probability that sales will be less than 4,900 oranges?d) What is the probability that sales will be less than 4,300 oranges?
A 50-mm-diameter, thin-walled metal pipe covered with a 25-mm-thick layer of insulation (0.085 W/mK) and carrying superheated steam at atmospheric pres- sure is suspended from the ceiling of a large room. The steam temperature entering the pipe is 120°C, and the air temperature is 20°C. The convection heat transfer coefficient on the outer surface of the covered pipe is 10 W/m² K. If the velocity of the steam is 10 m/s, at what point along the pipe will the steam begin condensing? i will 10 upvotes urgent
.A 45 kW rated solar power system has its power output and the Solar irradiance on the PV system measured during daylight hours over a day. Based on the following data, create a scatter plot of the power output of the PV system vs the solar irradiance and comment on the relationship between the two. Based on the data, can you tell which season this day was in? Solar Irradiance on the PV system (kW/m²) 0 0.079 0.333 0.571 0.751 0.86 0.914 0.93 0.904 0.803 0.606 0.345 0.054 Power output from the PV system (kW) 0 3.098 12.438 20.124 25.703 28.498 29.587 29.69 28.798 26.264 20.434 12.223 2
typing
do fast i will 10 upvotes.
(3) The Elon Company manufactures parts for an aircraft company using three computerized numerical controlled (CNC) turning centers. The company has to decide which machines are capable of producing a specific part with design specifications of 0.0970 inch ± 0.015 inch. The machines have the following parameters: Machine 1 (x= 0.0995, o = 0.004); Machine 2 ( = 0.1002, o = 0.009); Machine 3 (x = 0.095, o = 0.005). Determine which machines (if any) can produce the products within the design specifications. ||

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

SEE MORE TEXTBOOKS

12-87. The catapult is used to launch a ball such that it strikes the wall of the building at the maximum height of its trajectory. If it takes 1.5 s to travel from A to B, determine the velocity VA at which it was launched, the angle of release 0, and the height h.