11.3 (A) Calculate the strain energy stored in a bar of circular cross-section, diameter 0.2 m, length 2 m: (a) when subjected to a tensile load of 25 kN, (b) when subjected to a torque of 25 kNm, (c) when subjected to a uniform bending moment of 25 kNm. or the bar material E = 208 GN/m², G = 80 GN/m².

11.3 (A) Calculate the strain energy stored in a bar of circular cross-section, diameter 0.2 m, length 2 m: (a) when subjected to a tensile load of 25 kN, (b) when subjected to a torque of 25 kNm, (c) when subjected to a uniform bending moment of 25 kNm. or the bar material E = 208 GN/m², G = 80 GN/m².

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cast-iron bar with a square cross-section of 50 mm is reinforced by placing tw steel plates 50 mm wide and 10 mm thick on opposite sides of the cast-iron bar. The compound rod is 2 m long and is subjected to a suddenly applied load of 100 kN. Calculate: 2.2.1 the maximum stresses induced in both materials. 2.2.2 the instantaneous elongation of the compound rod; and 2.2.3 the strain energy stored in each material (EST= 200 GPa and Ec= 95 GPa).
PLEASE ANSWER ASAP THANK YOU
A solid brass [E = 93 GPa] axial member is loaded and supported as shown. Segments (1) and (2) each have a diameter of 23 mm and segment (3) has a diameter of 12 mm. Assume L₁ = 1.9 m, L₂= 1.3 m, L3 = 1.7 m, R = 36 kN, Q = 12 kN, and P = 24 kN. Determine: (a) the deformation of segment (2). (b) the deflection of joint D with respect to the fixed support at A. (c) the maximum normal stress in the entire axial member. (1) A L₁ R (2) L2 L3 (3) D P B C
If you have a material that is initially hard and strong, would you expect it to cyclically harden or soften? What would be a way of characterizing how strong it must be initially to make your answer a bit more quantitative?
C A cantilever beam is subjected to a downward force of 5 kN at its free end, as shown in Fig. 1. The beam is supported by a circular bracket (BD) attached to a wall. The bracket is made of ductile steel whose elastic limit is 300 MPa, both in tension and compression. Determine the diameter of supporting post using Von-Mises theory. (Hint: Neglected the weight of the beam, the ends B and D are welded) Fig.3 3 m B 2 m 2 m 2 m 5 kN
need correct ans
A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 602 MPa, and the Poisson's ratio as 0.20. Express your answer in three decimal places.
The extruded plastic shape has dimensions of D = 24 mm, d = 18 mm, a = 87 mm, and t = 3 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 335 N. (b) If the allowable shear stress for the plastic material is 2400 kPa, what is the magnitude of the maximum shear force Vthat can be applied to the extrusion? a Answer: (a) TA = КРа (b) V = N
Example 21.7. A conical bar tapers uniformly from a diameter of 4 cm to 15 cm in a length of 40 cm. If an axial force of 80 kN is applied at each end, determine the elongation of the bar. Take E= 200 GPa.
Please provide the correct solution asap. Handwritten recommended
Step by step process of solution.
i need the answer quickly