11.14 An abc-phase-sequence three-phase balanced wye-connected source supplies a balanced delta- connected load. The impedance per phase in the delta load is 12 + N. The line voltage at the source is V = 120 V3 /40° V rms. If the line impedance is zero, find the line currents in the balanced wye-delta System.

11.14 An abc-phase-sequence three-phase balanced wye-connected source supplies a balanced delta- connected load. The impedance per phase in the delta load is 12 + N. The line voltage at the source is V = 120 V3 /40° V rms. If the line impedance is zero, find the line currents in the balanced wye-delta System.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.25MCQ: For a balanced- load supplied by a balanced positive-sequence source. the line currents into the...

See similar textbooks

Similar questions

The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
A balanced three-phase source having a line voltage of 208-Vrms is supplying two parallel-connected three-phase loads. The first load is a balanced delta of impedance 21 angle 30° ohms per phase and the second load is a balanced wye of impedance 9 angle -60° ohms per phase. Find the magnitude of the rms line current(in Amperes) and the total average power absorbed by the load(in kW).
A balanced three-phase source having a line voltage of 208-Vrms is supplying two parallel-connected three-phase loads. The first load is a balanced delta of impedance 21 angle 30° ohms per phase and the second load is a balanced wye of impedance 9 angle -60° ohms per phase. Find the magnitude of the rms line current and the total average power absorbed by the load.
Suppose that a current source with Is amperes of current is connected in parallel to a pair of impedances Z₁ and Z2. Let I₁ be the current through Z₁ and 12 be the current through Z₂. Then, the total voltage Is is divided between 1₁ and 12 in proportion to impedance values Z₁ and Z2. a. True O b. False
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
4) A balanced delta connected load of ...+j18 ohm per phase is connected at the end of a three phase line as shown in figure. The line impedance is 1+j2 ohm per phase. The line is supplied from a three-phase source with a lie- to-line voltage of 207.85 V rms. Taking Van as reference, determine the following: a) Current in phase a. b) Total complex power supplied from the source. c) Magnitude of the line-to-line voltage at the load terminal. (Please determine the impedance value within the specified limits: 16-26 V. By considering the impedance value you determined yourself, solve the question.) ao- |V₂| bo Co- 1 +j2 Ω = 207.85 V www Figure a Jum ...+j18 n b
For a balanced- load supplied by a balanced positive-sequence source. the line currents into the load are 3 times the -Ioad currents and lag by 30. (a) True (b) False
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
Example: A balanced positive-sequence wye-connected 60 Hz three-phase source has line-to- line voltages of V,=1000 V. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.2 H inductance in series with a 100 0 resistance. Find the line-to-neutral voltages, the line currents, the power, and the reactive power delivered to the load. Assume that the phase of Van is zero.
A balanced positive-sequence three-phase source hasvan(t)=100 cos(377t+90°) V a. Find the frequency of this source in Hz. b. Give expressions for vbn(t) and vcn(t) c. Repeat part (b) for a negative-sequence source.