11. Water at 20 oC is flowing in a pipe of radius 1.0 cm. The viscosity of water at that temperature is 1.005 cp. If the flow speed at the center is 0.200 m/s and the flow is laminar, find the pressure drop along a 5 mm section pipe.

Q: 1. An incompressible fluid is flowing at steady state in the annular region (i.e., torus or ring…

A: Given Incompressible fluid

Q: Q2. Use the 1/7 power-law profile and Blasius's correlation for shear stress to compute the drag…

A:

Q: What rotational speed must be maintained in operating a 10-in. diameter centrifugal bowl handling a…

A: A centrifugal bowl of D=10in Liquid layer Thickness of fluid layer t=2in Density of fluid ρ=72.5…

Q: Air at atmospheric pressure flows across a staggered tube bank consisting of 8 rows of tubes in the…

A:

Q: Derive the velocity profile of the fluid inside the two stationary plates. The plate is initially…

A: Considering a small volume of a cube and velocity profile is obtained then it is integrated to…

Q: Shear stress profile for a Newtonian fluid flowing in a circular pipe is O A. Linear В. Parabolic…

A:

Q: what is the transfer function which relates the hight (h) to the inlet flow (F1) the Conical tank.…

A: Transfer function relating height to inlet flow is asked.

Q: A 4 inch Sched 40 steel pipe carries crude oil at 80°C. The crude oil has a dynamic viscosity of 1.2…

A: Given: 4 inch Schedule 40 steel pipe dynamic viscosity μ =1.2 x 10-2 Pa·s density ρ= 680 kg/m3

Q: Write down the 2 key parameters that affect the friction losses of the fluid flowing through a…

A:

Q: Consider the laminar flow of water in a 0.1-in diameter tube at a temperature of 60°F. The velocity…

A: Given that, Diameter of tube D = 0.1 in Average Velocity vavg = 2 ft/s The velocity profile is…

Q: 2. The jet airplane is flying at 80" in still air, A, at an altitude of 4 km. If the air flows past…

A: Velocity at B (VB) = 80 m/s Velocity at C (Vc) = 80 m/s ZB = Zc Density of air at altitude 4 km =…

Q: The pressure decreases across the length of a converging nozzle when the velocity of sound is…

A: The converging nozzle accelerates the flow whenever required. This is used in aircraft, dams, and in…

Q: For the water flow at 20 °C, use the manometer measurement to estimate the (a) centerline velocity…

A:

Q: The initial free fall of water from a faucet can be thought of as an inviscid flow because friction…

A: Given: The distance between points 1 and 2 is 7 cm i.e. z1 - z2 = 7 cm or 0.07 m The diameter of…

Q: HOMEWORK Derive the velocity profile of the fluid inside the two stationary plates. The plate is…

A:

Q: A smooth pipe consists of 8 m of 120 mm diameter pipe followed by 15 m of 300 mm diameter pipe with…

A: Water at 15 Degree CDensity ρ = 998 kg/m3Viscosity μ = 1.139 * 10-3 m2/sReynold number for small…

Q: What is the entropy increase through a convergent-divergent nozzle, if a normal shock occurs at a…

A: The entropy change of gas flowing in a nozzle is an isentropic process i.e. the change in entropy is…

Q: 2–92 A large plate is pulled at a constant speed of U 4 m/s over a fixed plate on 5-mm-thick engine…

A: Given data: U= 4 m/s Thickness t= 5mm= 0.005m Temperature 20oC Velocity Profile is given,

Q: Which among the statements is incorrect? (Α The flow velocity profile for turbulent flow is fairly…

A: The incorrect statement is:

Q: Consider a U-tube as shown in the Fig below, who's both arms are open to the atmosphere. If some…

A:

Q: Consider steady state, laminar flow of a fluid in the y direction between two parallel and vertical…

A:

Q: -1. An incompressible fluid is flowing at steady state in the annular region (i.e., torus or ring…

A: Given Incompressible fluid Take inner radius = r2 Outer radius = r1

Q: A disk 15 cm in diameter is placed in a wind tunnel at right angles to the incoming flow. The drag…

A: The drag force on the disk when water is flowing through it is to be estimated.

Q: : Determine the pressure difference between the two points in figure below Oil (S=0.75) X- ----- S,…

A:

Q: Calculate the kinetic energy changes

A:

Q: Compute the capillary rise in mm of pure water at 10 Celsius expected in an 0.8 mm diameter tube.

A:

Q: measures local or point velocities by measuring the pressure difference between the total pressure…

A: We have to answer which instrument is used to measure the point or local velocity by measuring the…

Q: An incompressible fluid is flowing at steady state in the annular region (i.e., torus or ring…

A: Given Incompressible fluid in coaxial cylinders

Q: For flow over a flat plate wherein a laminar boundary layer is present for the case of a zero-…

A:

Q: Paddle agitator

A:

Q: Water is in steady fully developed laminar flow between two horizontal, very wide (W) and long (L)…

A:

Q: Pascal second is the Unit of Oa. Viscosity O b. Surface tension O c. kinematic viscosity O d. Power

A: b) Surface tension:   SI Unit: N/m CGS Unit: dyne/cm kinematic viscosity (m2 s−1). The English…

Q: Which of the following statement is TRUE? (A) Friction factor f in laminar flow depends on the…

A: WE KNOW THAT,  Pressure drop = △P = 32 μVLD2  WHERE, V = velocity  if we doubled the velociy V2 =  2…