11. Steam at a pressure of 2MPA and temperature 300°C is passed at a constant rate into a desuperheater unit. The desuperheater is accomplished by continuously spraying water at 95 °C onto incoming superheated steam. The amount of water injected is so regulated that both the water and superheated steam finally change into dry steam at 2 MPa. If the resulting mixture of dry saturated steam leaves the desuperheater at 2MPA and the rate of I kg/s, find the mass of superheated steam used per hour and the mass of water to be injected per hour. Fond also the diameter of the pipe through which the superheated steam flows to the superheater if the speed of the steam through the pipe is not to exceed 25m/s.

11. Steam at a pressure of 2MPA and temperature 300°C is passed at a constant rate into a desuperheater unit. The desuperheater is accomplished by continuously spraying water at 95 °C onto incoming superheated steam. The amount of water injected is so regulated that both the water and superheated steam finally change into dry steam at 2 MPa. If the resulting mixture of dry saturated steam leaves the desuperheater at 2MPA and the rate of I kg/s, find the mass of superheated steam used per hour and the mass of water to be injected per hour. Fond also the diameter of the pipe through which the superheated steam flows to the superheater if the speed of the steam through the pipe is not to exceed 25m/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Stirling cycle operates with air with a volume flow rate of 0.5 m³/s at the beginning of isothermal compression. After compression, the volume flow rate is reduced by 75% of its initial volume. Assuming that the maximum pressure in the cycle is 1.2 MPa and if the heat rejected is 50 kW at 300 K, determine the mass flow rate of air and the ideal thermal efficiency of the cycle. Match each item to a choice: MASS FLOW RATE IDEAL THERMAL EFFICIENCY Choices: 79.65% 24.04% 0.3093 kg/s 23.05% 76.95% 0.5122 kg/s 0.4189 kg/s NONE OF THESE
I want to know how this four pressures and enthalpies are selcected
in a steam power plant, steam enters the turbine at 4 MPa and 500 C. The condenser pressure is 15 KPa. The turbine and pump isentropic efficiencies are 90 % and 85 %, respectively. Determine the actual net work in kJ/kg. In solving, use two decimal places for the enthalpies/energies while four decimal places for the steam quality. For the final answer, use two decimal places.
8
Question 3 Consider the turbocharger of an internal combustion engine. The exhaust gases enter the turbine at 450°C at a rate of 0.02 kg/s and leave at 400°C. Air enters the compressor at70°C and 95 kPa at a rate of 0.018 kg/s and leaves at 135 kPa. The mechanical efficiency between the turbine and the compressor is 95 percent (5 percent of turbine work is lost duringits transmission to the compressor). Using air properties for the exhaust gases, determine:(a).The turbine power output, compressor power input, air temperature at the compressor exit,(b).The air temperature at the compressor for the case of isentropic process and isentropic efficiency of the compressor.
CO2 is needed in a surgical suite for abdominal laparoscopic surgery. You have already designed a nozzle to step down the pressure from the gas cylinder to the delivery hose. The well-insulated delivery hose has a 2.2 mm inner diameter. The inlet conditions to the delivery hose are 103 psia and 17°C. Typically, the surgeon uses 4 to 6 L/min of gas at pressures between 10 to 20 mm Hg to inflate the peritoneal cavity; however, the delivery system must be able to provide flow rate of 17.5 L/min at 20.0 mm Hg for safety. The surgeon will use a pin valve to control the flow rate and maintain the operating space. The gas temperature should not be any colder than 10°C when delivered to patient, or tissue damage might occur. Determine the acceptable delivery hose length to meet the surgical criteria. State assumptions.
If saturated liquid steam at 850 kPa is throttled to 120 kPa, what is the quality of the resulting steam?
Refrigerant -134 a enters the evaporator of a refrigerator as saturated vapor at −20∘ C and leaves at −10∘ C and 100 kPa. The volumetric flow rate at the inlet is 0.25 m 3/s Calculate the mass flow rate.
in a steam power plant, steam enters the turbine at 3.5 mpa and 600 c. the condenser pressure is 15 kpa. the turbine and pump isentropic efficiencies are 95 % and 94 %, respectively. determine the actual net work in kj/kg. in solving, use two decimal places for the enthalpies/energies while four decimal places for the steam quality. for the final answer, use two decimal places.
200 m3/min is passed through the adiabatic humidifier. The condition of the air at inlet is 40C db and 15% RH and the outlet condition is 25C db and 20C wb. Find the amount of the water vapor added to the air per minute.
Consider a compressor which is used to compress steam (water) through an isentropic process. At the inlet the temperature is 600°C and pressure is 3 MPa. At the exit pressure is raised to 6 MPa. What is the temperature of the steam at the exit of the compressor? (You need to do interpolation to find the exact value) Assumptions. The compressor operates steadily.