The exhaust gas leaving an oil engine is passed through a heat exchanger which consist of tubes surrounding by water. The gas enters at 327 °C and leaves at 193 °C. The water enters the exchanger at 17 and leaves at 56 °C. If the mass flow rate of water is 2.54kg/min. Determine the mass flow rate of gas, take cp of the gas is 1.04 kJ/kg.

The exhaust gas leaving an oil engine is passed through a heat exchanger which consist of tubes surrounding by water. The gas enters at 327 °C and leaves at 193 °C. The water enters the exchanger at 17 and leaves at 56 °C. If the mass flow rate of water is 2.54kg/min. Determine the mass flow rate of gas, take cp of the gas is 1.04 kJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

mc,T, mc,T, -- šutma cooling water The cooling system given in the figure is fed with water at a flow rate of 15 g /s and a temperature of 80 ° C. The tank with a volume of 300 cm3 is cooled by cooling water. In steady condition, a heat of 500 cal /s is taken from the tank and the incoming water is cooled. When the unit step positive effect is given to the cooling water flow rate while operating the system in steady condition a) Find the transmission functions that connect the outlet temperature to the input variables and draw the block diagram. b) Find the change of fluid outlet temperature with time (tfin = 120s). Average cp for water = 1 cal / g° C and p = 1 g/cm3
Air at temperature 27 oC and pressure 66.3 kPa enters the diffuser steadily with a velocity of 190 m/s. The inlet area of the diffuser is 0.6m2. The air leaves the diffuser with nearly zero velocity. Determine the mass flow rate in kg/s of the air. Use R=0.287 kJ/kgK.
Air at 500K and 800kPa enters a nozzle and drops to 205K and 98.5kPa at the exit. Since the air entering the nozzle is 25m/s and its mass flow rate is 0.9k/s; Calculate the velocity at the outlet, the inlet and outlet cross-sectional areas of the nozzle. (Assume that the air behaves ideally and DeltaH(kJ/kg)= 0.35 DeltaT.)
Air is drawn into the compressor at pressure of 100 kPa and temperature of 22ºC. The volumetricflow rate at the compressor inlet is 0.4 m3/s. The compressor exit pressure is 900 kPa and thecompressor efficiency is 70%. The air leaving the compressor passes through a heat exchangerwhere it is cooled by transferring heat to the atmosphere at 22ºC. The outlet temperature of airafter the heat exchanger is 32ºC. The air passes through a valve and enters a 1 m3 rigid tank. Theinitial pressure and temperature of the air in the tank are 100 kPa and temperature of 22ºC,respectively. The final pressure and temperature of the air in the tank are 900 kPa and temperatureof 90ºC. During the filling process, the tank transfers heat to the surroundings (at 22ºC).Don’t assume constant specific heat.Determinea) The mass flow rate of air entering the compressor, ?̇ (kg/s).b) The rate of power consumed by the compressor, (kW).c) The rate of heat transfer from the heat exchanger to the atmosphere, (kW).d)…
Oxygen flows into a tube of 10cm diameter at 0.25kg/s, under 4.5atm pressure and 25°C temperature. It is then throttled by a valve to 2.5atm pressure. Find the entry and exit velocities of oxygen.
You are designing a system to mix fuel and air prior to ignition in an engine. Do you want the flow to be laminar or turbulent? Why?
With regard to the flash vessel, consider 10 bar steam (hg=2,782 kJ/kg) entering a turbine and leaving as condensate (i.e. a saturated liquid) also at 10bar (hf=782 kJ/kg). If the mass flow rate of the above condensate were 10 kg/s and it entered a flash vessel at 1.5 bar how much saturated steam (hg=2,717 kJ/kg) and saturated liquid (hf= 536 kJ/kg) could it produce?
. Steam at an initial enthalpy of 100 kJ/kg and inlet velocity of 100 m/s, enters an insulated horizontal nozzle. It leaves the nozzle at 200 m/s. Determine the exist enthalpy (in kJ/kg).
Q8. A gas enter a turbine with a velocity of 300 m/s and a temperature of 527 °C and specific internal energy of 688 kJ/kg and density of 2.7 kg/m³ . The gas expand adiabatically from a pressure of 620 kN/m² to 130 kN/m² .The gas leaves the turbine with velocity of 150 m/s. Determine the power output from the turbine in kilowatt. Take the mass flow rate of 4 kg/s. 00 limite through ongine Qvel 300 °C ond 50 9C tho hoot roiootod tompooretur
Dry saturated steam at 8 bar expands in a convergent nozzle to a pressure of 0.5 bar and 0.8 dryness fraction. Determine the exit velocity of the steam if the initial velocity of the stream is 125m/s
Steam (H2O) enters a turbine at 35 m/s and specific enthalpy of 3500 kJ/kg. Thesteam leaves the turbine as a mixture of vapor and liquid having a velocity of 60m/s and a specific enthalpy of 2400 kJ/kg. If the flow through the turbine is steady,adiabatic, and changes in elevation are negligible, calculate the work output per unitmass (kJ/kg) for the turbine.