11. In the mantle, density varies from 2.0 to 5.0 g/cm³, the bulk modulus varies from 0.0 to 6.6 x 1011 N /m² , and the rigidity modulus varies from 0.0 to 2.9. Determine whether density variations or variations in these elastic coefficients have the greatest effect on P-wave velocities. Plot Vp as a function of density and Vp as a function of the modulii. Units for each column can be found in the table below. modulus density Body wave velocities have form: velocity=. K + (4 /3)µ 2 +2µ Vp P wave velocity S wave velocity E wave velocity

11. In the mantle, density varies from 2.0 to 5.0 g/cm³, the bulk modulus varies from 0.0 to 6.6 x 1011 N /m² , and the rigidity modulus varies from 0.0 to 2.9. Determine whether density variations or variations in these elastic coefficients have the greatest effect on P-wave velocities. Plot Vp as a function of density and Vp as a function of the modulii. Units for each column can be found in the table below. modulus density Body wave velocities have form: velocity=. K + (4 /3)µ 2 +2µ Vp P wave velocity S wave velocity E wave velocity

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ASAP
a band moves at a speed V and is in contact with a surface of an oil tank with viscosity m. calculate the power in watts required if the belt is moving at 2.9 m / s over SAW 30W oil at 20 C with L = 2m, b = 60m, Nu = 329.0mm ^ 2 / s, rho = 0.9g / cm ^ 2 and h=3cm
The weight of the crate is 50 kg and the spring constant is 200 N/m in DB. Use g= 9.81 m/s2. What is the stretched length in DB? 1.572 m 3.606 m O 1.769 m O 1.837 m
In mechanical fluid
A flat-bottomed raft is traveling across a shallow lake at 6 ms-¹. The lake is 10 cm deep. If the raft has a surface area of 3 m² and the lake is full of water with viscosity of 0.001 Pa s, determine the force required to maintain the raft's speed. [0.18 N]
cuboid object made of iron (density 7.7x10^3 kg/m^3) ( 1 cm on each side) when placed in a container filled with water and mercury. Object floating between layer of water and mercury as in the figure fine how long this object has suck into the mercury. if water have a density 10^3 kg/m^3 and mercury have a density 13.6x10^3 kg/m^3
A steel rim, with a mean diameter of 1 m, rotates at 1 000 r/min. Determine thecircumferential stress-induced if the density of steel is 7.8 Mg/m3
While using the Heisler charts for a cylinder at time t = 10 sec and at a radial location of r/ro=0.6 =0.8 and Q/Qo= 0.7 where 0=T-T 0.=T.-T and 0 =T -T o o and Qo = PCPV(T¡-T∞) =0.4; 00 00 If the parameters associated with the cylinder are p=2700 kg/m and C =900 J/kg.C and volume of 1 m long cylinder = 0.1 m3 Calculate the maximum possible heat transfer from the cylinder to the environment per unit length of the cylinder if = 20°C; and T = 55 C T 00 Write only the numerical value after converting the unit in J/m.
An infinitely long cylindrical container has a cross section area of radius R, and is placed horizontally with gravity being in the −y direction, as shown in the figure. The cylinder is 50% filled with water (the shaded part), with density ρ. The other 50% of the volume in the cylinder is filled with air with constant pressure of p = p0. The length of the cylindrical container in the axial direction is W. c) Use control volume analysis and divergence theorem on the 4th quadrant water volume to compute the hydrostatic force acted on the 4th quadrant of the cylinder wall, as shown by the thickened line in the figure.
When there are only a few upstream calming distances available, the annular venturi meter is helpful for metering flows in pipe systems. The cylindrical component of the annular venturi meter is installed inside a pipe, as seen in the image. Between the upstream pipe and the area close to the cylindrical portion, the pressure differential is monitored. In the system, air flows under normal circumstances. 10 cm is the pipe's diameter. The interior pipe diameter to the diameter of the cylindrical portion is 0.8. Water pressure is measured to be off by 5 cm. Track down the system's volume flow rate. Assume the flow is constant, incompressible, and viscous, and that the velocity is distributed equally throughout the pipe sections. Utilize typical air conditions at 25 °C and 101 kPa.
A study of the physical characteristic of honey was conducted due to the large demand of royal jelly. A capillary tube viscometer was used by a researcher in determining the viscosity of the honey. The viscometer is 250 mm long with an outside diameter of 55mm and effective thickness of 2.5mm and was used horizontally so that the effect of gravity was neglected. At an ambient temperature of 300C the following data were collected: \ΔΡ (Pa) Q (cc/s) 10.0 1.25 12.5 1.55 15 1.80 17.5 2.05 20.0 2.55 What will be the stress produced per unit length in the tube used in the production of royal jelly if it has a radius of 5mm and a flow of 1 capsule per second. (1 capsule = 0.85 cc of royal jelly).
I need the answer as soon as possible