11. A piston-cylinder assembly shown below is initially containing 2g of air at STP. Heat is then added until the temperature of the air inside the system reaches 250°C and pressure of 3kPag. Determine the work done (k) by fluid due to expansion. Calculate also the required spring constant (N/mm) necessary to compensate the expansion of the cylinder. SPRING Air at STP D- 30cm Heat

Q: Produce a 3D solid model of the Guard casing and test boss

A: Given Test boss Guard casing To find 3D solid model

Q: Draw and discuss the FBD for the following system. • Label all forces and directions. • How many…

A: The free-body diagram of the given problem is shown below and the major forces and dimensions also…

Q: F3 8 Z 4 F2 F1 There are 3 forces acting on the eye bolt. Force F1 acts on the XY plane has a…

A: The value of force is in xy plane The value of force is  in yz plane The value of force is

Q: components are represented by the supports in t

A: The supported beam has no bending moment at their extreme positions thereby only reaction forces are…

Q: Points for stress vs strain (in image) Assume the compressive concrete strength (f’c) is 3,000…

A:

Q: Draft and annotate the 2D sketch of support using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Above is a 5 speed manual transmission gearbox. The gear selector fork is an assembly which the user…

A: Gear ratio is defined as ratio of driven gear's teeth to driver gear teeth. G1/2 = T2/T1 G1/3 =…

Q: NL/H=493 and T₁ = 8 ms Give your answer to the 2nd nearest decimal place. Juve Ln transitions. What…

A: Given data T1=8ms=0.008 sNL/H=493

Q: Translate the following set of equations into the index notation by using the rule of the free…

A:

Q: Use the following isometric drawing of a hospital to create a two-point perspective drawing. (Use an…

A: Use the following isometric drawing of a hospital to create a two-point perspective drawing. (Use an…

Q: Consider the data points (2,2), (4,6), (7,3), and (10,5), a) Find the equation for the parametric…

A:

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: Use creo parametcric 4.0 drawing to Sketch all the compulsary part and partial views, including…

A:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: Ae bes elole 15.3 15.1 Ø0.3|A-B 6.40 6.35 9.55 9.50

A: (1) coaxially tolerance.on left diameter = ∅ 6.5-0.05+0.00on right diameter = ∅9.5-0.00+0.05 maximum…

Q: Create the model shown in Figure 8-118. The views and dimensions of the model are given in the same…

A:

Q: 16. The entire top surface on the part below must be flat within 0.5 but each 25 X 25 patch must be…

A: The answer to the above mentioned question is given below

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.