11- What is the current through the motor winding of Fig. 12-54 when the gate voltage is low? When it is high? 12- The motor winding of Fig. 12-54 is replaced by another with a resistance of 6 V. What is the current through the winding when the gate voltage is high? VDD +12 V Figure 12-54 +10 V M) 10 Ω MTP4N80E

11- What is the current through the motor winding of Fig. 12-54 when the gate voltage is low? When it is high? 12- The motor winding of Fig. 12-54 is replaced by another with a resistance of 6 V. What is the current through the winding when the gate voltage is high? VDD +12 V Figure 12-54 +10 V M) 10 Ω MTP4N80E

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

question from book ELECTRONIC CIRCUIT DESIGN : Question No.3 A designer designs the circuit given in figure 3. You have to analyse it to find thefollowing parameters: a.VB ,VE, IE , IB, VS , VCE, VDS. Replace the JFET with D-typeMOSFET and find b.Vc ,VG ,VDS ,VCE c. Is there any difference between the parameters found forJFET.
1. Construct the BJT circuit shown in Figure 1 on your project board with VBB = 12V and Vcc= 12V. Given B = 220 vc 12 V R1 3 33 kn Rc 4.7 kn c2 10uF Vo ci 10uF Vi 2N3904 R2 { 10 kn RE 1.2kn Figure 1 2. Compute thevoltage across base, VB and base current, Is for circuit in Figure 1. Show your calculations.
Electronic1 In the Zener diode regulator below, the input varies between 18 V and 22 V. The Zener diode is a 500-mW device. Calculate the minimum and maximum values of R.
What is wrong with this circuit? * R₁10 kn V₁ 24 V D₁ 1N4744A 1 15 V The zener is open. O The zener is shorted or damaged O not enough data O reversed connection of zener diode + 4.790 VR₂ 2.5 k R₁
9. Show complete and detailed solution.
VDD- 10 Velt 106 ID2 I07 Assume the following: (a) M1 and M2 are matched (b) = 0 for all MOSFETS (c) L identical for all FETS. (d) ID2 = 50 µA. (e) W1=W2=W3=W6=W8 (f) W4=W5=2 x W2 (g) W7=3 x W8 (h) Except for W/L ratios establishëd by the photolithography design, the fabrication process is the same for all FETS. Pay attention to sign convéntions! Provide values for: ID3 ID4 ID7 ID5 = drain circuit for M5! (Trick question. Careful-look at the
Determine the output V and DC level voltages of the output. (The diodes are IDEAL) 100 V Ideal diodes 2.2 k2 2.2 ka 2.2 kf -100 V O A. +100 V /+31.8 V O B. +100 V/ +64.2 V OC. -50 V/ +31.8 V O D. Short circuit O E. +50 V/+31.8 V
7 Design a DC power supply with following specifications: • Use a full-wave rectifier. • Number of outputs: 3 i) Output 1 ii) Output 2 0-20 V adjustable-max 2A 0-(-20) V adjustable-max 2A ii) Output 3 • Operation temperature Constant 9V-max 2A 0-40 C Line regulation <0.01%+2 mV • Load regulation • High current and voltage protection <0.01%+2 mV Using integrated circuits is forbidden. You can only use integrated circuits in the regulator circuit.
How did the output voltage pf this power supply equals to 1 A
For the circuit shown below calculate IDQ in mA when IDSS=12mA VP=-6V and B=120
None
91 li suesam ba Experiment -7- oitoonnoo orit Voltage Regulator using Zener diodes R1 R2 Vo Fig-1- R1 12 R2 Vin Vo Fig -2- Write a short report Voltage Regulator using Zener diodes