11) The capacitive level transducer is to be used to measure the depth h of liquid in a tank between 0 and 8 m. The total length 1 of the transducer is 9m and the ratio bla of the diameters of the concentric cylinders is 3.0. The dielectric constant ɛ of the liquid is 2.4 and the permittivity of free space ɛo is 8.85pFm'. The transducer is incorporated into R, =100, R, =10kN and voltage source V, =15 volt , the capacitance Ch when the tank is empty is R Rs with the deflection bridge ETh 12) (e) For the same question in ( 11), the value of Co such that Eth is zero when the tank is empty is

11) The capacitive level transducer is to be used to measure the depth h of liquid in a tank between 0 and 8 m. The total length 1 of the transducer is 9m and the ratio bla of the diameters of the concentric cylinders is 3.0. The dielectric constant ɛ of the liquid is 2.4 and the permittivity of free space ɛo is 8.85pFm'. The transducer is incorporated into R, =100, R, =10kN and voltage source V, =15 volt , the capacitance Ch when the tank is empty is R Rs with the deflection bridge ETh 12) (e) For the same question in ( 11), the value of Co such that Eth is zero when the tank is empty is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Topic: Series Resistor and Voltage Division Consider the following two diagrams of series circuits. For each diagram, use arrows to indicate the direction of the conventional current. Then, make comparisons of the voltage and the current at the designated points for each diagram.
i need a code and diagram to make circuit arduino uno with these sensors MQ_7 gas sensor with (buzzer 4_8v DC) Dht11 flame detection sensor digital with (buzzer 4 - 8v Dc) hw 596 pressure alarm all these sensors show on Icd 20*4 i2c thanks
4. In your own words what is safety?
1- The recommended limit of voltage drop on a lighting circuit for a single-phase supply as per IEE Wiring regulations is equal to 6.3 volt. Then the value of supply voltage is a. 290V b. 250V c. 210V d. 230V 2- Which of the following statement is TRUE ? a. Resistance is not proportional to length of the material and Resistance is proportional to area b. Resistance is proportional to length of the material and Resistance is proportional to area c. Resistance is not proportional to length of the material and Resistance is inversly proportional to area d. Resistance is proportional to length of the material and Resistance is inversly proportional to area
The active component of line current in figure 1 is______. a. 12A b. 20A c. 12A d. 4A
can you do question iii please?
3.a. There may be installations where grounded conductors of different systems are installed within the sameraceway, cable, or box. In these cases, it's imperative that the system-grounded conductors remainA. spliced.B. disconnected.C. separated.D. buried.3.b. In dwelling units, the maximum allowable voltage between conductors that supply lighting fixtures isA. 220 V.B. 120 V.C. 115 V.D. 110 V.
Q3/ For the below cct find (V1, V2, 1, & Ix) 1A 2A 2. Ix
i need a code and diagram to make circuit arduino uno with these sensors MQ_7 gas sensor with (buzzer 4_8v DC) Dht22 flame detection sensor digital with (buzzer 4 - 8v Dc) hw 596 pressure alarm all these sensors show on lcd 20*4 i2c thanks
If an MLO has 4 aluminum conductors #3/0 (THWN) select a conduit for a "D" panel with three-phase, 120/208-V serving a duplex and other loads. (Use table 12.3 pp 152). O 2.5 in O 2.0 in O 3.0 in O 1.5 in
Find lo = Blank 1 Write your answer with unit with space in between. Round off to 2 decimal places. Ex. 10 V 10_2 ... M- I,1 20V O