11) 1. Tank A has 100 units of water. 2. Tank B has 20 units of water. 3. Tank A transfers 5 units of water to Tank B in 1 4. Tank B transfers 2 units of water to Tank C in 1 TANK A

Q: The progressive or gradual engagement of the teeth of helical gears gives the ability to transmit…

A: Given data: The progressive or gradual engagement of the teeth of helical gears gives the ability to…

Q: Find the value of a. TO a. Vs +3

A:

Q: solve and show every step with right answer

A: Data given - Rectangular cross section 225×75 mm2 Torsional moment = 20kN Axial Compressive force =…

Q: In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e = 7 cm. Find the value of angle a…

A:

Q: A compressor motor has a shaft diameter of 7⁄8 inch. The felt wiper that wrapstightly around the…

A: Given    Diameter,d = 7⁄8 inch.

Q: Tabulate the absolute coordinates. Write a program to drill the holes and mill the rectangular…

A: Given: To find: Write a program to drill holes and mill

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: Determine the thickness (mm) of a spur gear tooth with a diametral pitch of 7.01, measured along the…

A:

Q: The distributed load of w = (-2x² + 4x + 16) lb/ft acts on the beam as shown(Figure 1). Part A…

A:

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: solve by showing every step.

A: Given data: The ultimate tensile strength of component is Sut = 30 ksi. The ultimate compression…

Q: Solve for the mobility.

A:

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: 4. From the given figure, solve for the bar Y from the reference line . (choose the nearest answer)…

A:

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: solve 4 and 5 only

A: The given state of stress is:To find:(iv) The orientation of the elements for the maximum in-plane…

Q: For the laser cutting of the shown path, determine the absolute and incremental coordinates of the…

A: given; findabsolute and incremental co-ordinate;

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: The objects shown below have been rotated positively about one of the axes shown. the amount of…

A: According to the given data rotation amount and rotational axis is provided in the below picture.

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: o shafts 3679mm between centers carry pulleys 1288 mm in diameter and 910 mm in  diameter…

A: dL= diameter of larger pulley dS= diameter of smaller pulley C= distance between the centers of…

Q: a. Determine the magnitue of P and F (in N) if the resultant of the five force shown is 1000N…

A: The given system of force is as shown below, The given forces are as follows. F1=840…

Q: For the following internal dovetail, if bis 40mm greater than c, m is 60mm less than b, h is 25 mm…

A:

Q: A piston engine in which the bore and stroke are of equal dimension is referred to as a "square…

A: Given:Let bore be 'D' and stroke be 'L'For a square engine, D = LNo of cylinders, n = 8Displacement…

Q: Express:            50000mm3 as m3 3.5m3 as mm3 20m3 as cm3 45cm3

A:

Q: Mechanical properties of materials:   Strength of material:   Ultimate strength:   Yield…

A: Material property of property- To is critical to understand the mechanical properties of a material…

Safety guidelines for material handling

Material handling involves transportation and movement of materials (inventory) within the storehouse or warehouse. The process also involves efficient inventory management, which forms an essential part of any manufacturing or fabrication company.