10)When the gain 'k' of a system is increased, the steady-state error of the system: increases. remains unchanged may increase or decrease decreases

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: it is called as the difference between the value and the measured value of a quantity a. mistakes b.…

A: In this value we will find significant figures...

Q: Is Mc microfarads?

A: Given, The abbreviation of mc =?

Q: In a rectifier circuit , DC output voltage and RMS output voltage is  0.3 V & 0.48 V respectively.…

A: Form factor is ratio of root mean mean square to average value of output voltage of rectifier. Form…

Q: In an electronic circuit, a. current remains the same through all the series components. b. voltage…

A: Note that,  In an electronic circuit, current remains same jn all series components and voltage…

Q: What can you say about the topic: PHILIPPINE ELECTRICAL CODE 1

A:

Q: Khee Voltage of Ilicon semi nductor. (without Your answer A condition where zero (0) volt is less…

A: 1) Knee voltage of silicon semiconductor is 0.7

Q: & Prove That %3D

A: Resonance Resonance is the condition when the voltage across a circuit becomes in phase with the…

Q: 1. WRITE THE CKT. DIAGRAM OE FOUR BASIC TYPES OF SERIES CKT.

A: Series circuit A Series Circuit occurs when two or more loads are linked in series. If one load or…

Q: With neat diagram explain the construction and working of CRO.

A:

Q: In static characteristics, is defined as the difference between the true value applied to a…

A: in static characteristics, Accuracy is defined as the difference between the true value applied to a…

Q: Given the information appearing in Figure beside (assume Ic=IE) determine: (a) Ic. (b) VE. 18 V (c)…

A: Disclaimer:  Since you have asked multipart questions, we will solve the first three subpart for…

Q: The AND-OR implementation of PAL is having O a. Programmable AND array and Programmable OR array Ob.…

A: Given: Brief description: In the above given question they are discussing about the working of the…

Q: In a rectifier circuit , DC output voltage and RMS output voltage is  0.3 V & 0.6 V respectively.…

A:

Q: +V1ev1- L3 13/23 R2 v5 es V4 e4 |12/02 Figure 2060

A:

Q: Difference in the digital and the analog systems

A: Both digital and the analog systems are used to transmit and received information (or signals). The…

Q: IEEE and IEC standards

A: standards for electrical safetyIEC - international electrotechnical commissionIEEE - institute of…

Q: Q2: (A)Find the following: 1- (110)10+ (0111)2.by using BCD numbers. 3-(3E91)16- (1F93)16by using…

A: The number system is used to represent information in digital electronics. Different bases exist in…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: The is the construction of the available n- and p-type materials, that was constructed as our first…

A: 1)Diode  2) Reverse bias

Q: Briefly describe how a distance can be measured by the method of phase comparison

A: From the method of phase comparison, the distance is measured indirectly by determining the number…

Q: Define Analog

A: Analog can be defined as the signal, which is continuous. The analog signal has a time-varying…

Q: For The Volfage-divider bias configurafion of the hgure Shown below, determine: Vc ,VE B IBQ. I ca,…

A:

Q: Please show the work in between the rearranged formula and the answer

A: Given: Calculate the S/N in dB if the passband circuit is 48kHz to 64kHz and the maximum bit rate is…

Q: Experiment Title SIGNAL GENERATORS

A: WE have to discuss signal generator, The sine wave generator represents the largest single category…

Q: The neutral current is equal to three times of ....... sequence current.

A: Current in nautral is sum of three phase currents. Current in each phase is sum of possitive…

Q: From the table, what is the circular mils for the following: a. 14 AWG a. 10 AWG b. 30 AWG c. 20 AWG

A:

Q: 19. Identify the response time of a meter. a. Time taken by output to reach final constant value…

A: Identify the response time of a meter. It's depend on the parameter.

Q: Use block diagram formula

A:

Q: 3) What is the dropout ratio? What is the advantages of dropout ratio in power systems. (min 1 page)

A: A pick-up and drop-out ratio terms related to protective relays. The pickup current of a circuit…

Q: Question : Explain the concepts of lattice matched hetero-structure. Don’t copy other works.…

A: It is asked to explain the concept of lattice matched hetero-structure.

Q: diff b/w aproximated & Interp0leted Curves. (Brief explanation with sketches)

A: Graphs are the pictorial representation of the system when we vary one quantity with respect to the…

Q: 9Vpk pk Vin Vout 1.25 2.25 3.75 4.50 -1.25 -2.25 -3.75 -4.50

A: We need to find out output voltage for given input values in clamper circuit .

Q: 10. Describe with one sentence what the shape functions in FEM are.

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.