100kN is attached to the pin at A. Determine the tension in the horizontal cable. Also, determine the reactions at the hinge and roller. Neglect the weights of the bars. a. Determine the tensile force (kN) on the cable. b. Determine the vertical reaction (kN) of the hinge. Indicate its direction, use positive value if it is upward and negative if it's downward. c. Determine the horizontal reaction (kN) of the hinge. Indicate its direction, use positive value if it's to the right and negative if it's to the left. d. Determine the vertical reaction (kN) of the roller support. Indicate its direction, use positive value if it is upward and negative if it's downward.

100kN is attached to the pin at A. Determine the tension in the horizontal cable. Also, determine the reactions at the hinge and roller. Neglect the weights of the bars. a. Determine the tensile force (kN) on the cable. b. Determine the vertical reaction (kN) of the hinge. Indicate its direction, use positive value if it is upward and negative if it's downward. c. Determine the horizontal reaction (kN) of the hinge. Indicate its direction, use positive value if it's to the right and negative if it's to the left. d. Determine the vertical reaction (kN) of the roller support. Indicate its direction, use positive value if it is upward and negative if it's downward.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 3: Inputs: ● F = 1800 N P = 600 N (same as previous problem) a = b = 3 m (same as previous problem) c = 8 m (same as previous problem) The frame is comprised of two members. All joints are pinned. Compute the reactions at pins A and C, as well as the forces at pin B. P с a) Ax (Indicate left/right) b) Ay (Indicate up/down) c) Cx (Indicate left/right) d) Cy (Indicate up/down) e) Bx (no need to indicate direction since this is an internal force) f) a F B b C Net force in y-direction at pin B, using the FBD for bar BC. This is not necessarily By by itself. Again, no need for direction here.
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
2-2 A 100-N force is applied at end C of the rod as shown. c) Assess the effect of the angle being varied from 0° to 360° to the moment of the 100-N force about point A. [b) (i) MA=0 N-m; (ii) MA=-24k N-m; (iii) MA=-12k N.m] 2-3 A 600-N force is applied on end D of the bent rod as shown. c) Assess the effect of the angle being varied from 0° to 180° to the moment of the 600-N force about point A. [b) (i) MA= 180 N-m; (ii) MA= - 480k N-m; (iii) MA= 180k N-m; (iv) MA=- 432k N.m] Figure IA Figure 150 mm P2-2 600 N 50 cm B P2-3 90 mm 0 000 B 30 cm C 100 N 30 cm
I need this problem to be solved by the force method.
Consider the frame as shown in the figure. A moment of 80 kN-m acts at the joint O, given that the support at B fails at any moment greater than 18 kN-m. Then support B is (a) Unsafe (c) Just Safe A L, EI D L, EI D 80 kNm B L, EI L, EI C (b) Safe (d) Cannot be determined
The frame ABCDEF shown above is supported by a cable at D and a pin at A. A load of weight W = 45 lb hangs at point F.Neglect the weights of any individual members. Be sure to include a single free body diagram of the entire frame ABCDEF and individual free body diagrams of the parts that constitute this frame: Member ABCD Member CEF Member BE A. Determine the tension in cable GD, the magnitudes of components of the reaction forces at pin A, and the magnitudes of components of the reaction forces at pin C. B. Is member BE in tension or compression?
The wall crane supports a load of 700lb. Determine the horizontal and vertical components of reaction at the pins A and D. Also, what is the force in the cable at the winch W? The jib ABC has a weight of 100 lb and member BD has a weight of 40 lb. Each member is uniform and has a center of gravity at its center. 4 ft D A 4 ft- W 60° B 4 ft- E 700 lb
2. The scoop holds a 2,000 N weight concentrated at G. If all links are in duplicate, determine the vertical reaction at joint K (Fxy). Note that HL is connected to the truck body and LKJ is a single member. -320 mm 260 mm B 180 mm 100 mm D 160 mm K 1040 mm 380 mm |200 mm 1120 mm Answer: FKy = 403.3613 N ↑
The compound beam is pin supported at C and supported by a roller at A and B. Note that there is a hinge at D. Find the reactions at the supports. Neglecting the thickness of the beam. (Provide the whole solution along with its FBD)