100 MPa 75 MPa 150 MPa

Q: The element of material below is subjected to the state of stress shown, where a = 120.0 MPa, b =…

A:

Q: Oy Txy

A: given; normal stress in x direction =σxnormal stress in y direction =σyshear stress in xy…

Q: 100 MPa 75 MPa 150 MPa

A:

Q: he forces applied to pulleys are given as shown below. Accordingly, show the stress state at point A…

A:

Q: Construct a Mohr's circle for the following point stresses: o = 60MPa, oy = 10MPa and Txy = +20MPa,…

A:

Q: A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal…

A:

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

A:

Q: 2: haft shown below, determine the normal and A, including stress concentrations. Then dr and…

A: Given: r=0.0042 m d=0.03 m D=0.033 m P=1500 N M=300 Nm T=250 Nm

Q: Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches…

A: Given data: Weight of the bar, W = 6000 lb. Cable diameter, d = 0.6 in. Draw a free-body diagram…

Q: Two blocks joined by a single pin are subjected to a pulling force of P = 250 Ib. The pin has a…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: The state of plane stress at a point is shown on the element in Figure below. Represent this state…

A: Given: The orientation of element, θ = 45° The stress along x-axis, σx = -10 ksi The stress along…

Q: Calculate the values of ol and o3 in the rock if the differential stress is 40 MPa and the center is…

A: differential stress = 40 MPa. (diameter of the Mohr's circle).Therefore, the radius of the Mohr's…

Q: Problem 2: A state of plane stress at a point on the surface of a structure consists of the…

A: Givenσx=18ksiσy=24ksiτxy=15ksi

Q: At a point in a component, the state of stress is shown on the element below. Assume that the stress…

A:

Q: Determine the maximum normal stress on a transverse plane in the straight portion of the structure…

A: To find: The maximum bending stress at the bottom for the both the symmetrical and non-symmetrical…

Q: Determine the equivalent stress state of an element oriented 30° clockwise with respect to the…

A:

Q: When there is a plane stress condition as shown in the figure, display this stress in the form of…

A:

Q: There is a rectangular plate 2 mm thick on which the forces shown in the figure act. Determine…

A:

Q: The main stress, the maximum shear stress, and the dead angle are obtained when the stress is given…

A:

Q: Determine the equivalent state of stress on an element if it is oriented 30° clockwise from the…

A:

Q: Use Mohrs circle to find the principle stresses and determine the normal and shear stresses acting…

A:

Q: The horizontal force of P = 80 KN acts at the end of the plate. The plate has a thickness of 10 mm…

A: Given data as per question P = 80KN The thickness of plate =10 mm Area=10×200=2000 mm2 we know…

Q: State of stress at the wall and the roof of the following circular opening bafore the excavation is…

A: The state of stress at wall,  MPa

Q: Fill in the blanks. Draw and label the Mohr’s circle. For sigma-yp = 30 kSf. does this fail? Find…

A:

Q: P to point A of the section given in the figure Plot the normal stress distribution in the section,…

A: Given dataP=20kN Here are calculation the Moment of inertia about the neutral axis

Q: Try

A: Given Data : σx=60 MPa σy = 0 τxy = 40 MPa.

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.