100 mm 30 mm E, Н 60 mm C 40 mm 0.8 m 0.4 m- 10,2 ml 0.2 m

Q: as a diameter of 2 in. and a thickness of 0.20 in. Disk B is supplied with 15 hp of power of which A…

A:

Q: 1000 Nom 1060Nom TITTITIIT

A:

Q: The 54-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: A motor drives a shaft at 300 rpm and a power output of 100 kW. The shaft is made of A-36 steel and…

A:

Q: The 60-mm-diameter shaft is made of 2014-T6 aluminum (G=27 GPa). If the allowable stress is Tallow =…

A:

Q: If end B of the shaft, which has an equilateral triangular cross-section, is subjected to a torque…

A: Given data as per question Torque = 900 lb.ft Assuming G of the shaft = 3.7×103 ksi

Q: 1. The splined ends and gears attached to the A-36 steel shaft are subjected to the torques shown.…

A: Given data: d=40 mmShaft=A-36 steel Need to determine the angle of twist of end B with respect to…

Q: angle of twist

A:

Q: The torque of 250 kN.m produces a maximum shear stress of 48 MPa in the 8 m-long hollow steel shaft.…

A:

Q: 40-mm-diameter The steel shaft is subjected to the torques shown. Determine the angle of twist of…

A: To Find : The angle of twist of the end. Given : The young modulus is G=75 GPa. Free Body Diagram :

Q: 300 N-m 500 N-m The solid 30-mm-diameter shaft is used to 200 N-m transmit the torques applied to…

A: It is required to determine maximum shear stress

Q: The 63-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: the solid steel sheft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Please find the solution below.

Q: shear

A:

Q: The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: The diameter of the shaft DF is The power at F is The power at A is The power at B is The power at C…

Q: The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and…

A:

Q: The electric motor keeps the aluminum shaft ABCD, with rigidity modulus 27 GPa, operating at a…

A:

Q: *RIO4. The shaft has a radius cand is subjected to a torque per unit length of t, which is…

A: Given, Uniformly distributed Torque per unit length = to  radius of shaft = c  Length of Shaft = L…

Q: The composite shaft consists of a mid-section that includes the 1-in. diameter solid shaft and a…

A:

Q: Shaft AB is made entirely of steel and is solid with a uniform cross-section. Knowing that LAC = LBD…

A: Given data as per the question Length of AC section =290 mm = 0.29 m Length of CD section =90 mm =…

Q: The two shaft

A: Design of shaft is important process in any mechanical system. Design of shaft is determined by…

Q: 5-7. The solid shaft has a diameter of 0.75 in. If it is subjected to the torques shown, determine…

A: The shaft is subjected to different torsional moments at different locations but in between these…

Q: The 43-mm-diameter shaft is subjected to the torques shown. What is the angle of twist of end A with…

A: The given shaft can be drawn as, Free body diagram of CB and AB can be drawn as,

Q: The shaft is fixed at ends A and B and has a positive torque T a distance of 4m from A and 8m from…

A:

Q: The 80-mm-diameter shaft is made of steel. If it is subjected to the uniform distributed torque,…

A: Given Data: The length of the shaft is L = 800 mm. The uniformly distributed torque acting on the…

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: 4. The tapered shaft is made from E- 36 steel ( G = 80 GPa ), and has a radius which can be…

A: Given    Torque, T = 450 Nm    Length, L = 4 m Find     Angle of the twist

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.