10. The adsorption isotherm which is indicative of strong adsorbate-adsorptive interactions is: a. c. The H-type isotherm b. b. The L-type isotherm c. a. The S-type isotherm d. e. None of the above e. d. The C-type isotherm

Q: What are uses of I (iota) in the field of Civil engineering

A:

Q: Ex: The figure below is a proposed weir floor with three vertical piles. calculate the uplift…

A:

Q: At pH 5-7 aluminum hydroxide is O readily exceeding water quality limits for aluminum O leaving a…

A: 1. At pH 5-7, aluminum hydroxides are in their least soluble form. At a pH range of 5-7, the…

Q: Aggregate is also used for filter systems, is the attached image of a filter system correct in…

A: The given figure is of Slow sand filter with mixed aggregates (FSG). The given arrangement of…

Q: Ex:- For the Barrage shown in the figure below , use Khosla's theory:- a- Check the safety against…

A:

Q: 0 0 Influent- Influent Influent Anaerobic Aerobic Influent- Return activated sludge Aerobic Anoxic…

A: This question is related to the Environment Engineering from Civil Engineering. In this question ask…

Q: Sam, the strawberry producer, has had complaints from the produce company that his strawberries are…

A: Solution:- Given, Bulk modulus =225psi Compression modulus(∈1)  =200 psi Strawberry diameter=1.25 in…

Q: A sheet of BCC iron 1 mm thick was exposed to a carburizing gas atmosphere on one side and a…

A: Given:- The thickness of the sheet of BCC iron = 1 mm The carbon concentrations at the two surfaces…

Q: What is the meaning of the term "activated" applied to the adsorbent materials ?

A: The meaning of the term "activated" applied to the adsorbent materials is:

Q: EX: A hydraulic structures shown in fig. determine 1- the correction of uplift pressures at key…

A: Correction for the uplift pressure at key points  is given asC%=t·ϕ1-ϕ2dwhere t- thickness of the…

Q: Explain the process of adsorption of SO2 by a bed of copper oxide?

A: When coal is burner for energy sulphur dioxide is released because of the presence of sulphur in…

Q: Ex: By Bligh's and Lane's theory For the hydraulic structures shown below calculate : 1- Sketch the…

A:

Q: Ca+2 = 36.8mg/L Mg+2 = 2.9mg/L HCO3 = 98mg/L pH = 7.53 Temp = 9C Calculate the following: a.…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Please also explain how the height of the paraboloid is found for this problem.

A:

Q: Material Classifcation By Bond Type

A: Types of bonds, Stretcher bond, Header bond, English bond, main features of English bond,…

Q: A: Density bottle test: Sample 1: Dal = 0.9982 x (83.49-62.12) (251.3162.12) - (264.41-8 = 2.58 g/ml…

A: SampleDensity, g/cc12.5822.6132.6242.5352.5662.57

Q: C and AD so that the resultant of the three forces applied at A is vertical. 18 m

A:

Q: 8 - Which of the following properties is the difference that distinguishes Silica fume from other…

A: Silica is very useful in concrete because of its physical and chemical properties as well as…

Q: A saturated sand sample has a dry unit weight of 18 kN/m³ and a specific gravity of 2.65. If yw 9.81…

A: Given: A saturated sand sample has, Dry unit weight, γd=18 kNm3 Wet unit weight, γw=9.81 kNm3…

Q: Check the determinacy of the structures ir E B

A:

Q: the titrimetric determination of water hardness. Why?

A: In a hardness test , a titrant  of EDTA is added in small amount in titration. On addition of EDTA…

Q: What is the relationship between the silica structure and the Bowen's reaction discontinuous series?

A: Magma's mineral composition changes as it cools, as described by the Bowen reaction series. The…

Q: ) Explain the types of absorbent materials in term of: A. Its function. 3. Where best to be used. C.…

A: An absorbent material has small holes in it. When a liquid, such as water, comes into contact with a…

Q: Q4 In the same sketch, draw plausible longitudinal profiles of (a) specific energy head, (b) water…

A: Introduction : a ) Specific energy head : The total head relative to the channel bottom is known as…

Q: Which of the following is false regarding factor of safety in the design of structures?   a. It…

A:

Q: Determine the porosity for the rhombohedral packing of grains in a porous media.

A: Given data in question  Rhombohedral packing  Porous media To find out  Porosity Note Angle of…

Q: Minerals: A.can form by life-processes -- organic B.are crystalline solids C.have a unique chemical…

A: Answer Mineral is a non organic, naturally occurring homogeneous solid with having a definite…

Q: A plate has 0.25 wt% initial carbon concentration and is at 950C. The surface is then exposed t…

A: Given data,C0=Initial carbon concentration=0.25wt% at 9500CCS=suface exposed carbon maintained at…

Q: Determine the nominal flexural strength M, for the beam shown in the figure below. Assume that the…

A: Given, f'c = 4000 psi = 4 ksi fy = 60000 psi = 60 ksi b = 18 in h = 22 in ​ As=8 × 0.79 As= 6.32…

Temperature effects on atom arrangements

Atoms are the smallest units of matter. Atoms can be subdivided into electrons, protons, and several other subatomic particles. Groups or combinations of atoms form molecules that primarily decide the property and behavior of materials. These molecules have the property to attract other molecules based on the valence electrons in the atoms' outermost orbit. An orderly arrangement of molecules is known as crystal structure, which forms the fundamental topic of concern in materials science and engineering. The arrangement of molecules is different for different materials and hence, each material exhibits different lattice arrangements. The lattice arrangements are functions of external loads, deformations, and temperature. On experiencing high temperatures or low temperatures, the behavior of the lattice arrangement of a material change.