10. Measure the diameter of impression using the profile projector and compute for the hardness number using the formula: Where: 2P P - Applied Load D- Diameter of steel ball (8.0 mm) d - Ave. diameter of indentation BHN %3D AD(D D² – d² Raw data: Diameter Specimen (carbon steel) d1 d2 Air cooled 5.13 5.22 Oil quenched Water quenched 4.12 4.36 3.74 3.81 Note: All dimensions are in mm.

Q: Condition 3: The same structural support from Condition 2 is heated from room temperature of 25"C.…

A: Stress produces in the material due to changes in temperature is known as thermal stress. Condition…

Q: if the coldworked radius is twenty mm, now what is the radius before being deformed if the ductility…

A:

Q: Problems 145 For the data below, find the slope and intercept relating two hardness scales for…

A:

Q: A 2.0-inch diameter 4140 steel bar is austenized and tempered in oil without Agitation, determine…

A: Given:To find:Determine the hardness at 0.6 inches below the surface.

Q: The table gives data concerning the shrink fit of two cylinders of differing materials and…

A:

Q: A mild steel material is subjected to a Brinell hardness test with an applied force of 8145 N using…

A:

Q: 4. Determine zone of brittle, zone of ductile and brittle-to-ductile transition temperature base on…

A: Ductile material are those material which do not have any initial stress or strain in it. It obeys…

Q: What can be determined when looking at the hardness values? What about when it comes to material…

A: The hardness values shown in the image are obtained by performing a Vickers hardness test on four…

Q: reduction in area

A: Given: Initial diameter D=15.55 mmFinal diameter d=7.35 mm TO determine: The percentage reduction in…

Q: in 20 min and thank DYBALA 8

A:

Q: a. What is the Brinell hardness number (HB) for 1020 Steel that has been annealed at 785 "C? (Check…

A:

Q: Determine the indentation diameter and the surface area of indentation of a copper material…

A: Given: BHN = 955 D = 10 mm W = 9.4 kN Thus,  F=Wg=9.4×1039.81=958.2 kg

Q: 1. You are finding Young's modulus of a sample of wood, using the simply supported and centrally…

A: Disclaimer:Since you have asked multiple questions, we will solve the first one as per Bartleby…

Q: Question-7. Steady-state creep data taken for an alloy at a stress level of 160 MPa are given below.…

A: Given,  Data for stress level of 160 MPa The stress component , n =6.8 R = 8.3145 J/mol-K To find…

Q: A square cross-section v-notched specimen of height 75 mm has each side of 10 mm has been selected…

A: Given data  height of specimen (h) = 75 mm side = 10 mm thickness of notch = 1.9 mm    To determine…

Q: Determine the height h above the base of the centroid of the Assume a = 10.27 in., b = 12.07 in., c…

A:

Q: In a tensile strength test a metal bar with initial and final length of 2 in. and 2.195 in.…

A:

Q: A plate contains an internal flaw that extends through the plate thickness. The plate is to be…

A: (A) Write the given data. b=1 mc=100 mmLf=1.25 mma=9.34×10-2 mmY=1.03

Q: Determine the indentation diameter and the surface area of indentation of a copper material…

A: Given: The test force, P = 9.4 kN The diameter of the steel ball, D = 10 mm The Brinell hardness…

Q: Determine the indentation diameter and the surface area of indentation of a copper material…

A: (i) Write a value of the Brinell Hardness Number (BHN).   BHN=902   Write a diameter of the…

Q: Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C.…

A: Need help with condition 3 please

Q: For each question, provide an explanation, identifying the correct choice ( it is marked in red)…

A:

Q: 41) A 19mm diameter cylindrical rod is subject to extreme loading. It must withstand a 75000 N…

A: Given:

Q: Load (N) Al (mm) 0.0000 0.0296 0.0592 5,000 10,000 15,000 20,000 25,000 26,500 27,000 26,500 25,000…

A:

Q: You are given three metal test samples, with the same chemical composition and differing grain…

A:

Q: Calculate yield strength, ultimate tensile strength and modulus of elasticity both of material…

A:

Q: i) Initial Length (in mm) =  Answer for part 1 ii) Final Area (in mm2) =  Answer for part 2 iii)…

A:

Q: Q3/ the table below show the properties of three materials suggest to applicate as tooth filling…

A: In the given parameters, K refers to thermal conductivity of the material. It represents the ability…

Q: A soft steel specimen has a BHN of 150, find the equivalent 29 tensile strength in MPa. A. 393 B.…

A: There is a empirical relationship between the Brinell hardness number (BHN) and the tensile strength…

Q: A tension test was conducted for a cylindrical specimen of stain-less steel having an initial…

A: A tension test was conducted for a cylindrical specimen of stain-less steel having an initial…

Q: Strength of Materials Dr. Maad Abdullah Hussein AL-ESRAA UNIVERSITY COLLEGE 8. BRINELL TEST Material…

A:

Q: A structural support for a machine is subjected to a static compression load of 20 kN. The support…

A: Given data,  P= 20 kN =20000 N For the SAE 1040 HOT ROLLED steel.  Sy=414 MPa= 414 N/mm2

Q: 4. a steel at 110 ksi and 91 ksi, respectively. A data table is attached in the back of the test.…

A: 4.1. Can SAE 1040 steel be selected for this application? Ans :Yes, SAE 1040 steel can be selected…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.