10. An engine developing 30 brake horsepower must be cooled by a radiator through which water is pumped from the engine. Using the following factors: Heat transferred from engine to cooling water, expressed as horsepower, equals 40 HP. Water temperatures in radiator: Top water = 2000F. Bottom water = 1900F. Weight of 1 gallon of water = 8.33 lbs. Calculate the required rate of flow of water in gallons per minute. A. 15.4 gal/min B. 20.4 gal/min C. 123.4 gal/min D. 14.5 gal/min

10. An engine developing 30 brake horsepower must be cooled by a radiator through which water is pumped from the engine. Using the following factors: Heat transferred from engine to cooling water, expressed as horsepower, equals 40 HP. Water temperatures in radiator: Top water = 2000F. Bottom water = 1900F. Weight of 1 gallon of water = 8.33 lbs. Calculate the required rate of flow of water in gallons per minute. A. 15.4 gal/min B. 20.4 gal/min C. 123.4 gal/min D. 14.5 gal/min

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

convert to correct unit
Which of the following terms is not included in the mechanical energy balance? shaft work internal energy potential energy skin friction A dilute sugar-water solution enters a pipe with an ID of 3.05 inches at a rate of 15.6 ft^3/hr, then exits through a diameter of 6.4 inches. What is its velocity at the exit? 11.87 ft/hr 49.71 ft/hr 34.22 ft/hr 69.83 ft/hr O O O
21. The following are the results of tests conducted on a centrifugal pump. Negative pressure head in suction pipe close to pump =22 cms of mercur y Pressure he id in delivery pipe close to pump=1'50 kg/cm2 Difference of level between the two gauges 0 50 metres SHP of the electric motor Discharge of the pump * Dianeter of the suction pipe Diameter of the delivery pipe Calculate the overall efficieney of the pump. -32 hp -010 cumeo %3D =20 cma 18 cms (78 17%)
How many piston does a two stroke engine have
1- In a bike, the __________ is converted into power. A.kinetic energy B.heat energy C.work energy D.potential energy
10. When using a thermal flow meter to measure mass, the O Faster Slower O Neither O Both the fluid flows the cooler the temperature becomes.
11.1 Fluid Mechanics Provide complete solutions and detailed drawings with FBD. *make sure to answer the given table.
2. A car is traveling on a highway at 28 m/s. a) What is the pressure at the bottom of a car's gas tank. that is a cube with side lengths of 0.5 meters? Assume the tank is full of gasoline with a denisty of 800 kg/m^3. b) How much pressure does a pump need to supply in order to draw gasloine from the bottom of the tank to the top of the tank? The velocity of the gasoline once it is pumped out of the tank should be 1 cm/s; the gas at the bottom of the tank is at rest. c) The gasoline from part b flows through a tube (cylinder) of radius lcm before entering a larger tube of radius 10cm. What will the velocity of the gasoline be in the larger tube? d) The tires on the car have an outer radius of 0.2 meters. How many complete rotations did the tires go through in one hour? Hint: Determine how far the car travels in one hour. e) How many hours can the car travel before running out of gas? f) During your journey. you hit a pothole and have to change your tire. You get your spare…
2) A compressor system which is controlled by starting-and-stopping is composed of a compressor with pumping capacity of 50 m3/min of free air and a receiver tank of 20 m3. The circuit demand is 25 m3/min of free air. No of start/stops is required to be 15 every hour. If the maximum line pressure is 8 bar gauge, what must be the low level pressure ?
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 1, P1(gage)=______ A. Patm B. 0 C. 101.325 kPa D. It can not be determined.
Compressors work with the gas and air, while centrifugal pump transfers energy. Select one: O True False
Thermodynamics (Jet-Propulsion Cycle) Round up the answer up to 5 decimal places. A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure & temperature is found to be 14.7psi & 546R. The axial flow compressor provides a pressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of air inside the engine is 133 lbm/s. Determine the following: a. T-S diagram b. Pressure & temperature at each state c. Thrust force (lbf)